background image

 

172-65528A-01  (VS3-E/VS3-P/VS3-EP)  8 Jul 2015

 

11

 

 

EXPRESS LIMITED WARRANTY 

 
Subject to the limitations set forth below, TLV Corporation, a North Carolina corporation
(“

TLV

”) warrants that products which are sold by it or TLV International, Inc., a Japanese

corporation (“

TII

”), which products (the “

Products

”) are designed and manufactured by

TLV Co., Ltd., a Japanese corporation (“

TLVJ

”), conform to the specifications published

by TLV for the corresponding part numbers (the “

Specifications

”) and are free from

defective workmanship and materials. With regard to products or components
manufactured by unrelated third parties (the “

Components

”), TLV provides no warranty

other than the warranty from the third party manufacturer(s).

Exceptions To Warranty

This warranty does not cover defects or failures caused by:

1. improper shipping, installation, use, handling, etc., by other than TLV or service

representatives authorized by TLV; or

2. dirt, scale or rust, etc.; or
3. improper disassembly and reassembly, or inadequate inspection and maintenance

by other than TLV or service representatives authorized by TLV; or

4. disasters or forces of nature; or
5. abuse, abnormal use, accidents or any other cause beyond the control of TLV; or
6. improper storage, maintenance or repair; or
7. operation of the Products not in accordance with instructions issued with the

Products or with accepted industry practices; or

8. use for a purpose or in a manner for which the Products were not intended; or
9. use of the Products in a manner inconsistent with the Specifications; or

10. failure to follow the instructions contained in the TLV Instruction Manual for the

Product.

Duration Of Warranty

This warranty is effective for a period of the earlier of: (i) three (3) years after delivery
of Products to the first end user in the case of sealed SST-Series Products for use in
steam pressure service up to 650 psig; (ii) two (2) years after delivery of Products to
the first end user in the case of PowerTrap

®

units; or (iii) one (1) year after delivery of

Products to the first end user in the case of all other Products. Notwithstanding the
foregoing, asserting a claim under this warranty must be brought by the earlier of one
of the foregoing periods, as applicable, or within five (5) years after the date of
delivery to the initial buyer if not sold initially to the first end user.

ANY IMPLIED WARRANTIES NOT NEGATED HEREBY WHICH MAY ARISE BY
OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE AND ANY EXPRESS WARRANTIES NOT
NEGATED HEREBY, ARE GIVEN SOLELY TO THE INITIAL BUYER AND ARE LIMITED IN
DURATION TO ONE (1) YEAR FROM THE DATE OF SHIPMENT BY TLV.

Exclusive Remedy

THE EXCLUSIVE REMEDY UNDER THIS WARRANTY, UNDER ANY EXPRESS WARRANTY
OR UNDER ANY IMPLIED WARRANTIES NOT NEGATED HEREBY (INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE), IS

REPLACEMENT

; PROVIDED: (a) THE CLAIMED DEFECT IS REPORTED TO

TLV IN WRITING WITHIN THE APPLICABLE WARRANTY PERIOD, INCLUDING A DETAILED
WRITTEN DESCRIPTION OF THE CLAIMED DEFECT AND HOW AND WHEN THE CLAIMED
DEFECTIVE PRODUCT WAS USED; AND (b) THE CLAIMED DEFECTIVE PRODUCT AND A
COPY OF THE PURCHASE INVOICE IS RETURNED TO TLV, FREIGHT AND

 

Summary of Contents for VS3-E

















Reviews: