background image

 

172-65142M-04  (TC8)  11  Oct  2021

 

12

 

TLV EXPRESS LIMITED WARRANTY 

Subject to the limitations set forth below, TLV CO., LTD., a Japanese corporation 
(“

TLV

”), warrants that products which are sold by it, TLV International Inc. (“

TII

”) 

or one of its group companies excluding TLV Corporation (a corporation of the 
United States of America), (hereinafter the “

Products

”) are designed and 

manufactured by TLV, conform to the specifications published by TLV for the 
corresponding part numbers 

(the “

Specifications

”) and are free from defective 

workmanship and materials. The party from whom the Products were purchased 
shall be known hereinafter as the “

Seller

”. With regard to products or components 

manufactured by unrelated third parties (the “

Components

”), TLV provides no 

warranty other than the warranty from the third party manufacturer(s), if any. 

Exceptions to Warranty 

This warranty does not cover defects or failures caused by: 
1.  improper shipping, installation, use, handling, etc., by persons other than 

TLV, TII or TLV group company personnel, or service representatives 
authorized by TLV; or 

2.  dirt, scale or rust, etc.; or 
3.  improper disassembly and reassembly, or inadequate inspection and 

maintenance by persons other than TLV or TLV group company personnel, or 
service representatives authorized by TLV; or 

4.  disasters or forces of nature or Acts of God; or 
5.  abuse, abnormal use, accidents or any other cause beyond the control of 

TLV, TII or TLV group companies; or 

6.  improper storage, maintenance or repair; or 
7.  operation of the Products not in accordance with instructions issued with the 

Products or with accepted industry practices; or 

8.  use for a purpose or in a manner for which the Products were not intended; or 
9.  use of the Products in a manner inconsistent with the Specifications; or 
10.  use of the Products with Hazardous Fluids (fluids other than steam, air, 

water, nitrogen, carbon dioxide and inert gases (helium, neon, argon, krypton, 
xenon and radon)); or 

11.  failure to follow the instructions contained in the TLV Instruction Manual for 

the Product. 

Duration of Warranty 

This warranty is effective for a period of one (1) year after delivery of Products to 
the first end user. Notwithstanding the foregoing, asserting a claim under this 
warranty must be brought within three (3) years after the date of delivery to the 
initial buyer if not sold initially to the first end user. 

ANY IMPLIED WARRANTIES NOT NEGATED HEREBY WHICH MAY ARISE BY 
OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY 
EXPRESS WARRANTIES NOT NEGATED HEREBY, ARE GIVEN SOLELY TO THE 
INITIAL BUYER AND ARE LIMITED IN DURATION TO ONE (1) YEAR FROM THE DATE 
OF SHIPMENT BY THE SELLER. 

Exclusive Remedy 

THE EXCLUSIVE REMEDY UNDER THIS WARRANTY, UNDER ANY EXPRESS 
WARRANTY OR UNDER ANY IMPLIED WARRANTIES NOT NEGATED HEREBY 
(INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 
A PARTICULAR PURPOSE), IS 

REPLACEMENT

; PROVIDED: (a) THE CLAIMED 

DEFECT IS REPORTED TO THE SELLER IN WRITING WITHIN THE WARRANTY 
PERIOD, INCLUDING A DETAILED WRITTEN DESCRIPTION OF THE CLAIMED 

Summary of Contents for TC8
















Reviews: