TLV PowerTrap GP5C Instruction Manual Download Page 2

Page: 2 / 30

172-65637MA-05 (GP5C PowerTrap) 8 Jun 2020

Contents

Introduction......................................................................... 2

Safety Considerations ........................................................ 3

General Description............................................................ 5

Application ................................................................................................................ 5

Operation............................................................................ 6

Specifications ..................................................................... 7

Configuration ...................................................................... 8

Installation .......................................................................... 9

Open System Piping (Steam System Example) ........................................................ 9

Installation Procedure ............................................................................................. 10

Sizing the Condensate Receiver ............................................................................. 14

Maintenance Space and Tolerance Angle for Installation 15

Operation and Periodic Inspection ................................... 16

Operation ................................................................................................................ 16

Periodic Inspection and Diagnosis .......................................................................... 17

Disassembly/Reassembly ................................................ 18

Replacement Parts ................................................................................................. 19

Recommended Tools List for Disassembly/Reassembly ......................................... 20

1. Before Removing/Reattaching ............................................................................ 21

2. Removing/Reattaching the Body from/to the Cover ............................................ 21

3. Removing/Reattaching the Snap-action Unit ....................................................... 22

4. Removing/Reattaching Each Unit ....................................................................... 23

Troubleshooting................................................................ 24

Determining the Problem from the Symptoms......................................................... 24

Types of Failure and their Causes .......................................................................... 25

Causes and Corrective Measures ........................................................................... 26

Product Warranty ............................................................. 28

Service ............................................................................. 29

Summary of Contents for PowerTrap GP5C






























Search results

Summary of Contents for PowerTrap GP5C

Reviews:

Related manuals for PowerTrap GP5C

Brands by name

Popular brands

TLV PowerTrap GP5C, Instruction Manual

Search results

Summary of Contents for PowerTrap GP5C

Reviews:

Related manuals for PowerTrap GP5C

Brands by name

Popular brands