background image

 

 

 

 

 

 

General 

The  Sirius  iX30  card  reader  is  a  versatile  card  reader  which  support  multiple  card  technologies  and 
communication  protocols  used  in  access  control  solutions.  In  addition,  the  Sirius  iX30  is  able  to  support 
different technologies simultaneously. 

2.1 Wiring  

This document assumes standard T-568-B color coding of the cables. 

 

Picture T-568B 
 
 
 
 

 
 
 

 

2.2 Tools and equipment 

When  installing the Sirius iX30, the following tools or materials may be needed. 
 

 

T-568B, or another cable which meets the requirements as specified in chapter 4.4:  

 

Wire side cutter 

 

Electric wire ferrule  

 

Crimping tool 

 

Flathead screwdriver  

 

Drilling machine (if mounted on a surface) 

 

2x 6MM plug 

 

2x with the plug corresponding screw (screwhead must be 6mm at least). 

 

 

Pin  number 
RJ-45 Plug 

TIA/EIA-568-B

 

Cable color 

Signal ID 

T568B Pair 

White/orange 

DA+

 

2

 

Orange 

DA-

 

2

 

White/green 

DB+

 

3

 

Blue 

DC+

 

1

 

White/blue 

DC-

 

1

 

Green 

DB+

 

3

 

White/brown 

DD+

 

4

 

Brown 

DD-

 

Summary of Contents for iX30


















Reviews: