background image

 

 

 

 
12 
 

4.4.1  RS485 Directly 

Recommended cable type between the a Orion or Polyx and the Sirius iX30 card reader is:  
 

 

CAT 5 UTP four twisted pairs of 24AWG copper conductors 

 

CAT 6 UTP four twisted pairs of 24AWG copper conductor 

 

A  direct  connection  (without  using  an  Adapterboard)  between  the  Sirius  card  reader  and  a  door  controller 
based on RS485

™ is 

NOT 

possible when: 

 

Sirius and door controller

™ are installed in different buildings and thus the connection leaves 

the building 

or

 

 

the wiring is no UTP cable (CAT5 or CAT6) 

or

 

 

an existing (non UTP) cable is reused 

or

 

 

overvoltage protection for the card reader is required 

or 

 

An external power supply is required for the card reader. 
 

If any of the above conditions applies, see chapter 

5.4.2. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

4.4.2  RS485 via Adapterboard 

 
Recommended cable type between a Polyx and the Sirius card reader, using an Adapterboard is: 

 

Shielded cable with twisted pairs 
 

If a direct connection is not possible, 

an Adapterboard must be placed between Orion or Polyx and the 

Sirius iX30 card reader. 
 
Adapterboard is connected with the door controller with a default UTP cat5 cable (or higher) (plug connection). 

 

Pin  number 
RJ-45 Plug 

TIA/EIA-568-B

 

Cable color 

Signal 

Sirius iX30 pin 

White/orange 

B

 

Orange 

A

 

White/green 

B

 

B

 

Blue 

VCC

 

5-16VDC 

White/blue 

-

 

Green 

A

 

White/brown 

 

Brown 

GND

 

GND 

Summary of Contents for iX30


















Reviews: