manualshive.com logo in svg

Titanium 58058, Owner'S Manual & Safety Instructions

Share
Download
Titanium 58058 Owner'S Manual & Safety Instructions Download Page 10

Page 10

For technical questions, please call 1-888-866-5797.

Item 58058 

        

Sa
F

ety

Opera

ti

O

n

Maintenance

Speci

F

ica
ti

O

n

S

Filter Lens replacement

1.  Remove the Lens Frame from the Helmet Shell.

2.  Remove the Auto-Darkening Filter 

from the Lens Frame.

WarninG!  tO preVent SeriOUS inJUry 
anD BLinDneSS: 
replace the filter lens OnLy with an exact 
replacement.  Other lenses may not protect 
properly from welding light, or may not fit helmet 
closely enough to block all light at the edges.

3.  Remove any protective film from 

both sides of the new Lens.

4.  Install new Filter Lens into the Lens Holder 

and replace Lens Holder into Shell.

Battery installation or replacement

There is a battery indicator in the top 
left corner of the Display Screen

To install Battery:

1.  Remove the Automatic Filter from the Lens Holder.

2.  Slide the Battery Housing out of the 

Auto-Darkening Filter. Remove the used 
battery (if applicable). See Figure D

note:

 All used batteries must be properly disposed of.

3.  Place a new CR2450 Lithium Battery inside 

the Battery Holder and put the Battery Holder 
back into the Auto-Darkening Filter.  Make 
sure the new Battery is installed correctly.

4.  Replace the Auto-Darkening Filter into the Lens 

Holder and replace Lens Holder into Shell.

common problems and remedies

1. 

irregular Darkening Or Dimming

a.  Headband has been set unevenly on 

both sides of helmet (unequal distances 
from the eyes to filter’s lens).

b.  Reset Headband to reduce difference 

in distances to filter, if necessary.

2. 

auto-Darkening Filter Does 
not Darken Or Flickers

a.  Front Lens Cover is soiled or 

damaged (change the cover).

b.  Sensors are soiled (clean surface of the sensors).
c.  Welding current is too low (adjust sensitivity).

3. 

Slow response

Operating temperature is too low (do not 
use at temperatures below 14° F).

4. 

poor Vision

a.  Front/Inside Lens Cover and/

or Filter soiled (change it).

b.  Insufficient ambient light.
c.  Shade number is incorrectly set 

(reset shade number).

5. 

Welding Helmet Slips

Headband is not adjusted properly 
(adjust to fit head snugly).

Stop using the Helmet immediately if any 
of these problems cannot be corrected.

Summary of Contents for 58058













Reviews:

No comments

Brands by name

Popular brands

Load more brands