background image

24

Focus 500

GB

TESTING OF THE UNIT

For safety reasons, we would recommend having the device 

checked by an expert as required but at least every 12 months 

to ensure that it can continue to operate safely.

In the case of unused devices, the check can be postponed 

until they are next started up.

All (potentially deviating) national inspection and mainte-

nance regulations must also be observed.

If you have any questions, please contact the customer service 

team at Titan.

NOTE ON DISPOSAL 

In observance of the European Directive 2002/96/EC on waste 

electrical and electronic equipment and implementation in 

accordance with national law, this product is not to be dis-

posed of together with household waste material but must be 

recycled in an environmentally friendly way!

Titan or one of our dealers will take back your used Titan waste 

electrical or electronic equipment and will dispose of it for you 

in an environmentally friendly way. Please ask your local Titan 

service centre or dealer for details or contact us direct.

IMPORTANT INFORMATION ON PRODUCT LIABILITY

According to an EU directive, the manufacturer is only liable 

without limitation for faults in the product if all parts come 

from the manufacturer or have been approved by the manu-

facturer and have been mounted to the device and are operat-

ed properly. If third-party accessories or spare parts are used, 

the manufacturer is exonerated wholly or partly from his/her 

liability if use of the third-party accessories or spare parts have 

caused a defect in the product. In extreme cases, the relevant 

authorities can completely prohibit using the entire device.  

With original Titan accessories and spare parts, compliance 

with all safety regulations is guaranteed

GUARANTEE DECLARATION

Titan Tool, Inc., (“Titan”) warrants that at the time of delivery 

to the original purchaser for use (“End User”), the equipment 

covered by this warranty is free from defects in material and 

workmanship.  With the exception of any special, limited, or 

extended warranty published by Titan, Titan’s obligation un-

der this warranty is limited to replacing or repairing without 

charge those parts which, to Titan’s reasonable satisfaction, 

are shown to be defective within thirty-six (36) months after 

sale to the End User.  This warranty applies only when the 

unit is installed and operated in accordance with the recom-

mendations and instructions of Titan.

This warranty does not apply in the case of damage or wear 

caused by abrasion, corrosion or misuse, negligence, ac-

cident, faulty installation, substitution of non-Titan compo-

nent parts, or tampering with the unit in a manner to impair 

normal operation.

Defective parts are to be returned to an authorized Titan 

sales/service outlet.  All transportation charges, including re-

turn to the factory, if necessary, are to be borne and prepaid 

by the End User.  Repaired or replaced equipment will be 

returned to the End User transportation prepaid.

THERE IS NO OTHER EXPRESS WARRANTY.  TITAN HEREBY 

DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING, 

BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY AND FIT-

NESS FOR A PARTICULAR PURPOSE, TO THE EXTENT PERMIT-

TED BY LAW.  THE DURATION OF ANY IMPLIED WARRANTIES 

WHICH CANNOT BE DISCLAIMED IS LIMITED TO THE TIME 

PERIOD SPECIFIED IN THE EXPRESS WARRANTY.  IN NO CASE 

SHALL TITAN LIABILITY EXCEED THE AMOUNT OF THE PUR-

CHASE PRICE.  LIABILITY FOR CONSEQUENTIAL, INCIDENTAL 

OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS 

EXCLUDED TO THE EXTENT PERMITTED BY LAW.

TITAN MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 

PARTICULAR PURPOSE WITH RESPECT TO ACCESSORIES, 

EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT 

MANUFACTURED BY TITAN.  THOSE ITEMS SOLD, BUT NOT 

MANUFACTURED BY TITAN (SUCH AS GAS ENGINES, SWITCH-

ES, HOSES, ETC.) ARE SUBJECT TO THE WARRANTY, IF ANY, OF 

THEIR MANUFACTURER.  TITAN WILL PROVIDE THE PURCHAS-

ER WITH REASONABLE ASSISTANCE IN MAKING ANY CLAIM 

FOR BREACH OF THESE WARRANTIES.

Subject to modifications

TESTING OF THE UNIT / INFORMATION ON PRODUCT LIABILITY / GUARANTEE DECLARATION

Summary of Contents for Focus 500




















Reviews: