background image

General Description

This airless sprayer is a precision power tool used for spraying
many types of materials.  Read and follow this instruction
manual carefully for proper operating instructions,
maintenance, and safety information.

Operation

This equipment produces a fluid stream at extremely high
pressure.  Read and understand the warnings in the
Safety Precautions section at the front of this manual
before operating this equipment.

Setup

Perform the following procedure before plugging in the power
cord of an electric unit.

1. Ensure that the suction set/siphon tube and the return

hose are attached and secure.

2. Using a wrench, attach a minimum of 50’ of 1/4” nylon

airless spray hose to the unit.  Tighten securely.

3. Attach an airless spray gun to the spray hose.  Using two

wrenches (one on the gun and one on the hose), tighten
securely.

Make sure all airless hoses and spray guns are electrically
grounded and rated for at least 3200 psi (220 bar) fluid
pressure. 

4. Make sure the pressure control knob is in its OFF position

in the black zone.

5. Make sure the ON/OFF switch is in its OFF position.
6. Fill the oil cup with one tablespoon of piston seal lubricant

(Piston Lube).

Never operate unit for more than ten seconds without
fluid.  Operating this unit without fluid will cause
unnecessary wear to the packings.

7. Make sure the electrical service is 120V, 15 amp minimum.
8. Plug the power cord into a properly grounded outlet at

least 25’ from the spray area.

Always use a minimum 12 gauge, three-wire extension cord
with a grounded plug.  Never remove the third prong or use
an adapter.

CAUTION

CAUTION

WARNING

NOTE: Do not attach the tip to the spray gun yet.

Remove the tip if it is already attached.

WARNING

Siphon

Hose

Motor

Circuit 

Breaker

Filter

Return 

Tube

ON/OFF 
Switch

Oil Cup

Pressure 
Control
Knob

PRIME/ 
SPRAY 
Valve

Fluid
Section

Outlet 
Fitting

4

© Titan Tool Inc.  All rights reserved.

Preparing a New Sprayer

If this unit is new, it is shipped with test fluid in the fluid section
to prevent corrosion during shipment and storage.  This fluid
must be thoroughly cleaned out of the system with mineral
spirits before you begin spraying.

Always keep the trigger lock on the spray gun in the
locked position while preparing the system.

1. Place the suction tube into a container of mineral spirits

that has a flash point of 140ºF (60ºC) or above.

2. Place the return hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure

control knob to the “Min” setting in the yellow zone.

4. Move the PRIME/SPRAY valve down to the PRIME

position.

5. Turn the unit on by moving the ON/OFF switch to the ON

position.

6. Allow the sprayer to run for 15–30 seconds to flush the

test fluid out through the return hose and into the waste
container.

7. Turn the unit off by moving the ON/OFF switch to the OFF

position.

Preparing to Paint

Before painting, it is important to make sure that the fluid in the
system is compatible with the paint that is going to be used.

Always keep the trigger lock on the spray gun in the
locked position while preparing the system.

1. Place the suction tube into a container of the appropriate

solvent for the material being sprayed (refer to
recommendations of the material manufacturer).  An
example of the appropriate solvent is water for latex paint.

2. Place the return hose into a metal waste container.
3. Set the pressure to minimum by turning

the pressure control knob to the “Min”
setting in the yellow zone.

4. Move the PRIME/SPRAY valve down to

the PRIME position.

5. Turn the unit on by moving the ON/OFF

switch to the ON position. 

6. Allow the sprayer to run for 15–30 seconds to flush the old

solvent out through the return hose and into the metal
waste container.

7. Turn the unit off by moving the ON/OFF switch to the OFF

position.

8. Move the PRIME/SPRAY valve up to the SPRAY position.
9. Turn the unit on.

NOTE: Make sure that the spray gun does not have a

tip or tip guard installed.

Max.
PSI

Cle

an

Min.
PSI

CAUTION

NOTE: Incompatible fluids and paint may cause the

valves to become stuck closed, which would
require disassembly and cleaning of the
sprayer’s fluid section.

Clean

Min. 
PSI

Max.
PSI

Turbo PulseClean 

(red zone)

OFF 

(black zone)

Min. – 1800 PSI

(yellow zone)

OFF 

(black zone)

1800 – 3200 PSI

(green zone)

Pressure Control Knob

CAUTION

English

Summary of Contents for 640i





















































Reviews: