background image

© Titan Tool Inc.  All rights reserved.

25

Hydraulic System

1

2

3

4

6

7

8

9

10

11

17

18

19

20

21

25

23

29

30

28

25

31

22

24

26

27

13

14

15
16

12

5

32

33

34

35

37

38

39

9

10

42

46

28

24

43

44
45

41

40

36

Item

Part #

Description

Quantity

1

313-755

Knob decal ...............................................1

2

862-414

Set screw..................................................1

3

448-243

Pressure control knob ..............................1

4

860-520

Set screw..................................................1

5

448-250

Pulley/fan assembly .................................1

6

448-494

Key, pump (.156 x .156 x 1

3/16

) .................1

7

449-751

Hydraulic pump ........................................1

8

431-042

Tube connector ........................................1

9

858-636

Screw, HH ................................................8

10

858-002

Lock washer ...........................................10

11

325-031

O-ring .......................................................1

12

448-253

Return hose assembly .............................1

13

451-029

Fitting........................................................1

14

449-616

Tank cover ................................................1

15

858-609

Clinch nut .................................................1

16

858-621

Socket screw ............................................2

17

859-001

Washer .....................................................2

18

858-624

Screw .......................................................2

19

449-605

Tank gasket ..............................................1

20

112-208

Nipple .......................................................1

21

472-500

Elbow, street.............................................1

22

448-208

Inlet screen...............................................1

23

449-623

Hydraulic tank...........................................1

24

862-411

Flex lock nut .............................................2

25

862-001

Flat washer...............................................6

26

862-002

Lock washer .............................................4

27

449-212

Plug ..........................................................1

28

862-493

Screw, HH ................................................2

29

862-496

Tap bolt.....................................................1

30

448-232

Belt guard brace.......................................1

31

448-242

Shield .......................................................1

32

192-228

Elbow........................................................1

33

449-126

Hose clamp ..............................................1

34

420-250

Tubing, 

PTFE

...........................................1

35

448-246

Pressure hose assembly..........................1

36

192-051

Elbow........................................................1

37

101-205

Ground lug................................................1

38

451-220

Hydraulic filter...........................................1

39

449-609

Hydraulic by-pass.....................................1

40

449-626

Hydraulic fluid cap/dipstick.......................1

41

449-614

Tube assembly .........................................1

42

862-438

Thumb screw............................................1

43

862-402

Acorn nut ..................................................1

44

449-107

Mounting plate retainer ............................1

45

449-135

Spacer ......................................................1

46

862-480

Screw, HH ................................................1

47

451-121

Elbow (not shown)....................................1

48

941-555

Ball valve (not shown) ..............................1

Torque and Sealant Guide

Item

Description

4

Use blue Loctite on threads

8

Use hydraulic sealant

13

Use hydraulic sealant

16

Use blue Loctite on threads

16

Torque to 8 FT/LBS (11 N/m)

18

Torque to 8 FT/LBS (11 N/m)

20

Use hydraulic sealant

21

Use hydraulic sealant

22

Use hydraulic sealant

28

Torque to 15 FT/LBS (20,5 N/m)

29

Torque to 15 FT/LBS (20,5 N/m)

38

Torque to 20 FT/LBS (28 N/m)

46

Torque to 15 FT/LBS (20,5 N/m)

Summary of Contents for 335-305

































Reviews: