page 39
EvERFRESH
®
WATER CARE SYSTEM
The EverFresh water care system is comprised of the following products:
• FreshStart
®
10,000
Pre-filter
• Sodium dichlor
• Monopersulfate (MPS)
• FreshWater
®
III high output ozone system
• FreshWater
Ag+
®
silver ion purifier
FreshStart
10,000
Pre-filter
is used when filling a spa for the first time or at refill. It attaches to a garden hose and filters out rust, dirt, detergents, algae
and chemicals.
Sodium Dichlor (chlorine)
is the only recommended sanitizer that will work in conjunction with all of the other products in this system.
FreshWater III high output ozone system
uses Corona Discharge technology to produce a high concentration of ozone which is injected into the spa
water.
Monopersulfate (MPS)
is an oxidizing chemical used to prevent the buildup of contaminants, maximize sanitizer efficiency, minimize combined
chlorine, and improve water clarity.
FreshWater
Ag+
silver ion purifier
introduces silver ions into the spa water, inhibiting bacteria growth. When combined with MPS, or chlorine,
oxidizes particulates in the spa water.
It is important to follow the recommended application and maintenance programs outlined for each product’s use.
If the spa is being used over an extended period of time, such as a whole afternoon or evening, additional sanitizer will be needed.
A weekly “shock treatment” is required.
The shock treatment quickly destroys any remaining contaminants while revitalizing the silver ion cartridge, allowing the silver ions to continue to be
released into the water. Without this weekly shock treatment, the silver ion cartridge may stop releasing silver ions into the water.
To weekly “shock treat” your spa you may use either MPS or sodium dichlor. It will require much less sodium dichlor to administer the shock
treatment than MPS (one teaspoon of sodium dichlor has oxidizing capabilities comparable to two tablespoons of MPS). Sodium dichlor may be a
more appropriate weekly shock for those users that experience heavy bather load conditions.
EVERFRESH
®
WATER TREATMEnT gUIdE
At spa
startup
or refill
Follow Start-Up and Refill Procedures section
NOTE:
Use the
FreshStart
10,000
pre-filter when filling the spa
to remove unwanted contaminants.
Prior to
each use
(Test before adding any
chemicals; do not add
any chemicals if proper or
higher levels are found.)
Add one-half (½) teaspoon of
chlorine per 250 gallons
Caspian
™
(Model CHP)
Bengal
®
(Model M / MM)
Sumatran
®
(Model N)
⅔ teaspoon
⅔ teaspoon
⅔ teaspoon
Add one (1) tablespoon of
monopersulfate (MPS)* per 250 gallons
Caspian (Model CHP)
Bengal
(Model M / MM)
Sumatran (Model N)
1⅓ tablespoons
1⅓ tablespoons
1 ¼ tablespoons
Once a
week
Add one & one-half (1½) teaspoon
of chlorine per per 250 gallons
Caspian (Model CHP)
Bengal
(Model M / MM)
Sumatran (Model N)
2 teaspoons
2 teaspoons
1¾ teaspoons
Add three (3) tablespoon of
monopersulfate (MPS)* per 250 gallons
Caspian (Model CHP)
Bengal
(Model M / MM)
Sumatran (Model N)
4 tablespoons
4 tablespoons
3½ tablespoons
Every four
months
Drain and refill your spa.
Replace the
FreshWater
Ag+
silver ion purifier
NOTE:
Use the
FreshStart
10,000
pre-filter when filling the spa
to remove unwanted contaminants.
As
needed,
if
water is hazy,
cloudy or has
an odor
Add one & one-half (1½) teaspoon
of chlorine per per 250 gallons
Caspian (Model CHP)
Bengal
(Model M / MM)
Sumatran (Model N)
2 teaspoons
2 teaspoons
1¾ teaspoons
*MPS is an oxidizer, not a sanitizer.
Water quality and Maintenance
OR
OR
Summary of Contents for Bengal
Page 1: ......
