manualshive.com logo in svg

Thuraya T2M-DUAL, User Manual

Share
Download
Thuraya T2M-DUAL User Manual Download Page 26

24

Thuraya T2M-DUAL

This section outlines the standard installation guidelines for the installers. During the 
installation, the installer should take all the necessary safety precautions. The installer 
should take every precaution in order not to damage the vehicle during the installation 
procedure. The general installation procedure is as follows. 

1.  Prepare for the installation.

2.  Select proper locations for antenna and terminal. 

3.  Mount the antenna.

4.  Mount the terminal

5.  Rout the SAT & GPS antenna cable

6.  Connect the 26pin I/O cable

7.  Key on and operating.  

6.1  PREPARE FOR THE INSTALLATION 

Before installation, the installer should prepare the following:  

1.   Prepare the necessary tools and auxiliary materials for required for mounting the 

hardware

2.   Set the terminal using “T2M-DUAL Management Tool” for communication mode, 

selectable data, server IP, short code and any other necessary configurations. 

3.   Insert the SIM cards and back up battery into the terminal and set the vehicle 

voltage DIP switch.

4.  Affix the back cover and fasten the screws. 

6 Installation 

ü

   The installation must be done by a skilled installation professional.

ü

   The installer must comply with all safety precautions and not to 

damage the vehicle. 

ü

   Before the start of the installation of the terminal, Set the terminal 

parameters using the “T2M-DUAL Management Tool”. 

Summary of Contents for T2M-DUAL





































Reviews:

No comments

Brands by name

Popular brands

Load more brands