background image

4

This is the safety alert symbol. It is used to alert you to 
potential personal injury hazards. Obey all safety mes-
sages that follow this symbol to avoid possible injury or 
death.

DANGER 

indicates an imminently hazardous situation 

which, if not avoided, will result in death or serious injury.

WARNING

 indicates a potentially hazardous situation 

which, if not avoided, could result in death or serious 
injury.

CAUTION

 indicates a potentially hazardous situation 

which, if not avoided, may result in minor or moderate 
injury.

CAUTION 

used without the safety alert symbol indicates 

a potentially hazardous situation which, if not avoided, 
may result in property damage.

NOTE 

provides additional information that is useful for 

proper use and maintenance of this tool. If a 

NOTE 

is 

indicated make sure it is fully understood

NOTE

IMPORTANT SAFEGUARDS

Some dust created by spraying, blowing, power sanding, sawing, grind-
ing, drilling and other construction activities contains chemicals known 
to the State of California to cause cancer, birth defects or other repro-
ductive harm. 

Reduce your exposure to these chemicals by wearing approved safe-

ty equipment such as dust masks that are designed to filter out microscopic particles.
Use of this product will expose you to chemicals known to the State of California to 
cause cancer, birth defects, and reproductive harm.

 AVOID INHALING VAPORS 

AND DUST. WASH HANDS AFTER USING.

UNPACKING & INSPECTION

After opening the carton, unpack your new Spray Gun and related parts & accessories.
Please inspect it carefully for any damage that may have occurred during transit. Please 
check it against the photograph on carton. If any parts are missing, please contact our via 
E-Mail: [email protected].

Summary of Contents for H827C





















Reviews: