THUNDER TIGER Tiger Trainer MKIII Assembly Instruction Manual Download Page 2

INTRODUCTION

Tools

-Model  assembly can be much easier if the proper

tools   are  used.    Therefore   we  have  included  in  our
checklist to above,  a  complete  listing of all the tools we
used  to  assemble  our  prototype  models.   As  you  will
notice,    many  household  tools  can  be  utilized  during
construction.

Engine

  The Thunder Tiger GP-42 and F-54S are the ideal

engines for this airplane. These quiet running engines are
easy to start, require no special break in periods, are very
easy to maintain and will last for years.

Flight Equipment

    There are  several  “support”  items

that you will need to purchase in order to get your engine
running and your plane in the air. These are listed at the
bottom.

ITEMS NEEDED

Introduction

A checklist is also provided on the next page which
will make shopping for these items easier.

OTHER ITEMS REQUIRED FOR
ASSEMBLY

Radio 

- A 4- channel   radio   with  4  standard  servos   is

required.    Most   lower  priced  4-channel    radios   only
come  with  three standard  servos  so  you may  need  to
purchase  the  fourth  servo  separately.

Comprehensive Items Needed Check List

     4-Channel Radio with 4 Standard Servos

     5-Minute Epoxy (4 ounces or so)

     30-Minute Epoxy (4 ounces or so)

     “Thin” Instant Adhesive (1/2 ounce)

     “Thick” Instant Adhesive (1/2 ounce)

     Hobby Knife and Blades

     Epoxy Mixing Sticks and/or Brushes

     Sandpaper (150 grit)

     Masking Tape

     Rubbing Alcohol

     Paper Towels

     Ruler

     90 Degree Triangle

     Waxed Paper

     Fine-Point, Felt-Tip Pen

     Misc. Household Tools

     Drill and Bits (1/16", 5/64", 3/32")

Flight Equipment Needed Check List

     

Foam Rubber Padding for the radio

     Stick on Lead Strip for balancing the plane

     3 or 4 Props (see engine instructions)

     10%-15% Glow Fuel

     Fuel Pump or Bulb

     Electric Starter or “ Chicken Stick”

     Glow starter

     Extra Glow Plug(s)

     Silicon Tubing

Adhesives

- You will need two types of adhesives for the 

Tiger   Trainer - Epoxy    and    Instant   ( cyanoacrylate )
adhesives.  We  recommend  that  you  purchase both 5-
minute  and  30-minute  epoxy  to  cut down on assembly
time, but you can get by with only 30-minute epoxy if time
is no important.    You will also need a small bottle of both
"Thick" and "Thin" instant adhesive. 

All of us at Thunder Tiger want to thank you for choosing the best looking, easiest 
building and best flying ARF trainer available the Tiger Trainer 40.The kit features state-
of-the-art engineering that provides quick and easy assemble of a strong, yet lightweight 
airplane that will give you an enjoyable and educational experience.

To gain the most from this airplane kit, it is important that you read the instructions 
thoroughly and then follow them exactly. This instruction manual has been written with a 
novice modelers in mind, but includes many hints and modeling tips that even 
experienced modeler can benefit from. We strongly suggest that you read through the 
construction sequence and eliminate many questions you might have if you did not read 
the manual prior to starting the actual construction.

The first thing you should do before beginning assembly is to check the contents of your 
kit against the parts list on pages 4 and 5. If any parts are missing, contact your dealer or 
authorised Thunder Tiger Distributors immediately for replacement.

3

2

No.9041  

No.9800

INTRODUCTION...........................................................................................2
OTHER ITEMS REQUIRED............................................................................2
ITEMS NEED CHECK LIST.............................................................................3
PARTS LIST...............................................................................................4-5
PRE-ASSEMBLE NOTES...............................................................................6
WING.........................................................................................................6-8
FUSELAGE...................................................................................................8
INSTALL THE ENGINE................................................................................8-9
INSTALL FUEL TANK...................................................................................10
TAIL.......................................................................................................10-12
INSTALL THE RADIO..............................................................................12-13
BALANCE & FINAL ASSEMBLY FLIGHT..................................................14-16

TABLE OF CONTENTS

Tiger Trainer 

MK

Carry Master

-Thunder

Tiger offer a complete
organizer of field
equipment.  All  you
need is included.

No.1263-65

ACCESSORIES

12V DC Starter

- Provides high

torque starting power to start
your outboard engine.

Sealed Battery

- 7Ah 12V

Sealed Battery.

No.2674

No.2624

Summary of Contents for Tiger Trainer MKIII









Reviews: