THUNDER TIGER hawk 1400 Assembly Manual Download Page 4

AS6240  Tail Feathers (T. Magenta)
AS6240L  Tail Feathers (T. Blue)
AS6240Y  Tail Feathers (T. Yellow)

AS6239  Main Wing (T. Magenta)
AS6239L  Main Wing (T. Blue)
AS6239Y  Main Wing (T. Yellow)

PE0009  Hardware Set

AS6242  Motor

AS6241  Canopy

AS6026  6x3 Folding Prop

AS6238  FRP Fuselage

AS6245  Pushrods

Aileron Servo Tray(1)

Wing Protector(1)

Wing Join Wire(1)

CA Hinge(6)

3x12mm Wood Screw(2)

Servo Tray(1)

Motor Mount(1)

Wing Mount(2)

Fuselage(1)

Left Wing(1)

Right Wing(1)

Left V Tail(1)

Right V Tail(1)

Canopy(1)

2x5mm

Wood Screw(3)

3x3mm Set Screw(2)

Pin(2)

Blade(2)

2x8mm Screw(1)

Spinner(1)

Back Plate(1)

380 Motor(1)

Aileron Pushrod(2)

Hex Wrench(1)

EZ Connector(2)

M2 Nut(2)

3x3mm Set Screw(2)

Clevis(4)

Capacitor(2)

2.5x5mm Screw(2)

M2 Washer(2)

AS6244  Decal (T. Magenta)
AS6244L  Decal (T. Blue)
AS6244Y  Decal (T. Yellow)

Decal(1)

Elevator Pushrod(1)

AS6243  Control Horn

2x22mm Screw(2)

Nylon Horn(2)

Backplate(2)

Control Horn Base(2)

Open the box and check that you have all the parts as shown below. 

If anything is missing please contact your dealer

PARTS  DRAWING

Summary of Contents for hawk 1400













Reviews: