THUNDER TIGER hawk 1400 Assembly Manual Download Page 1

A

Allm

mo

os

stt  R

Re

ea

ad

dy

y  T

To

o  F

Flly

y

1.4M Electric Powered R/C Sailplane

Warranty

:This kit is guaranteed to be free from defects in material and workmanship at the date of

purchase.    It does not cover any damage caused by use or modification.  The warranty does not extend

beyond the product itself and is limited only to the original cost of the kit.  By the act of building this user-

assembled kit, the user accepts all resulting liability for damage caused by the final product.  If the buyer

is not prepared to accept this liability, it can be returned new and unused to the place of purchase for a

refund.

Notice:  Adult Supervision Required

:This is not a toy.  Assembly and flying of this

product requires adult supervision.  Read through this book completely and become familiar with the

assembly and flight of this airplane.  Inspect all parts for completeness and damage.  Customers in North

America please call 1-949-833-7498 for help  if you encounter any problems.

No.4312   E-HAWK 1400

Wing Span: 55" (1400mm)  

Length: 31” (787mm)  

Wing Area: 300 sq.in.(19.4dm

2

)  

Weight: 21oz.(600g)

Wing Loading: 10oz./sq.ft.(31g/dm

2

)  

Motor: 380PH Motor included  

Prop: 6 x 3 Folding Prop included

Summary of Contents for hawk 1400













Reviews: