THUNDER TIGER Agusta A109, Assembly Manual

Page: 6 / 16

1. Get your Raptor 90 well tuned before you install the
body. Remove the tail transmission, landing skid and
rotor head.
2. Locate the landing gear includes retracts, wires,
wheels, collars, POM washers, wheel spacers and
setscrews.
3. Secure the main retract wire with the setscrew which
is already in the retract shaft. Adjust the wire at 50mm
(1-31/32") in length then insert POM washer, wheel
then secure the collar with setscrew.
4. Same way to assemble the nose gear and adjust the
wire at 65mm( 2-1/2 ") in length.
5.Locate the main plate, retract mount, servo tray, M3
locknuts, standoff, 3x12mm and 3x25mm socket
screws as shown in the photo.
Front Fuselage (1)
Rear Fuselage (1)
Tail End (1)
Exhaust Pipe (2)
Horizontal Tail (2)
Wind Shied (L/1,R/1)
Middle Window (L/1,R/1)
Sun Roof (L/1,R/1)
Front Window (L/1,R/1)
Rear window (L/1,R/1)
Front Lower Window (L/1,R/1)
Pos t(2)
Rod End (2)
Carbon Rod (1)
Body Retainer (L/1,R/1)
M3 Lock Nut (8)
M3 Washer (12)
Sokcet Screw 3X8mm(4)
Socket Screw 3X10mm(8)
Wheel (3)
Retract (3)
Nose Landing Gear (1)
Main Landing Gear (2)
POM Washer (3)
Collar (3)
Setscrew (3)
Wheel Spacer (3)
Main Plate (1)
Retract Mount (2)
Front Horn (1)
Rear Horn (1)
Socket Screw 3X6mm(3)
Socket Screw 3X12mm(10)
Socket Screw 3X20mm(1)
Socket Screw 3X25mm(6)
Socket Screw 3X35mm(4)
Standoff Ball 8mm(3)
Standoff Ball 10mm(2)
Standoff Ball 12mm(2)
Standoff Ball 18mm(1)
Threaded Rod 30mm(2)
Threaded Rod 45mm(1)
Threaded Rod 60mm(1)
Servo Tray (1)
Coupler (2)
Standoff (2)
Ball End (8)
Z-Bend Pushrod (2)
3X10mm SinK Head Screw (12)
M3 Locknut (30)
M2 Nut (8)
POM Washer (2)
M3 Washer (9)
Carbon Rod (1)
Wood Mount (1)
Decal (1)
Wire Strike Strut (L/1,R/1)
Foot Step Support (4)
Hoist MNT (2)
Hoist(1)
Lower Antenna (2)
Upper Antenna (2)
Lower Wier Strike (1)
Upper wire Strike (1)
Wiper Base (2)
Foot Step (1)
Wiper (2)
Retaining Collar (32)
Handle Rail (2)
Cap (2)
Mounting Strip (2)
Hoist MNT Rod (4)
Wiper Mount (2)
2X6mm Self-Tapping Screw (4)
2X6mm Screw (4)
M2 Nut (4)
Silicon Tube (1)
Tail Boom Foam Retainer (1)
Tie Band (1)
Screen (S/1)
Screen (L/2)
2X5mm Wood Screw (23)
3X25mm Setscrew (2)
Muffler Extension (1)
4X60mm Muffler Bolt (2)
Tail Skid (1)
POM Washer (6)
Kit Contents
Fuselage
Horizontal Tail
Windshield
Retaining Set
Retract Gear
Decoration set
Hardware
Retract MNT&Linkage
Integrated Wood MNT
Decal
6.Secure the retract mount and the servo tray on the
main plate. Next locate retract gear, 3x10mm sink head
screw, M3 locknut, retract servo, 3x12mm socket
screw, M3 locknut and washer as shown.
7 6
PARTS CHECK LIST