Thrane&Thrane TT-3026L easyTrack Page 22 Installation Manual Download | Manualshive

Page: 22 / 60

background image

TT-3026L easyTrack Transceiver

Installation Manual

22/

60



Place the friction gasket on the surface.



Connect the cable and mount the screws.

4.1.1.2

P

OLE MOUNT

1”

40-3026 Opt. 101 is a standard 1” pole mount, Illustrated in

Figure 8.



Pull the cable in the pole and adapter.



Connect the cable to the transceiver.



Mount the adapter on the transceiver using screws.



Tighten the adapter to the pole.



Adjustable between 20 - 35 millimetre

NOTE: THE POLE MOUNT DEVICE HAS TO BE

DISCONNECTED FROM THE TRANSCEIVER WHEN THE

CABLE IS MOUNTED.

Figure 8 1" Pole mounting

«
...
20
21
22
23
24
...
»

Summary of Contents for TT-3026L easyTrack





























































Reviews:

No comments

Related manuals for TT-3026L easyTrack

Brand: OMCA Pages: 72

Brand: Barko Hydraulics Pages: 92

Brand: ParaBody Pages: 6

Brand: Sailmon Pages: 10

Brand: B&W Tek Pages: 12

Brand: B&G Pages: 129

Brand: b&o Pages: 46

Brand: Badger Meter Pages: 16

Brand: Cadman Pages: 84

Brand: Cannon Pages: 70

Brand: Sakai Pages: 31

Brand: MadLab Pages: 7

Brand: Landoll Pages: 144

Brand: Castellini Pages: 299

Brand: Lowenstein Medical Pages: 457

GrainLogix XLB10

Brand: LOFTNESS Pages: 104

Brand: Marani Pages: 35

SystemRoMedic RiseAtlas450

Brand: Handicare Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands