THORLABS RBD201 User Manual Download Page 40 | Manualshive

Page: 40 / 80

background image

40

HA0302T Rev A Feb 2016

Chapter 5

Stopping

- the way in which the jog motion stops when the demand is removed.

Immediate

- the motor stops quickly, in a non-profiled manner

Profiled

- th e motor stops in a profile d manner using the jog Velocity Profile

parameters set above.

Step Distance

- The distance to move when a jog command is initiated. The step size

is specified in real world units (mm).

Backlash Correction

- Backla sh is a te rm used to d escribe the errors inh erent in

motors which use a leadscrew. Brushless linear DC motors that have no leadscrew

and therefore this parameter is normally set to 0.
For motors which do incorporate a leadscrew, when this parameter is set, the system

will overshoot the demanded set point by the specified amount, and then reverse.
This ensures that durin g absolute or rel ative moves, the target position is alwa ys

approached in a forward direction. The Backlash Correction Distance is specified in

real world units (millimeters).
To remove backlash correction, this value should be set to zero.
Note. Setting a negative value for backlash correction also results in zero correction.

Persist Settings to Hardware -

Many of the parameters that can be set for the RBD201

series drivers can be stored (persisted) within the unit itself, such that when the unit

is next powered up these settings are applied automatically. This is particularly

important when the driver is being used manually via a joystick, in the absence of a

PC and USB link. The

Move and Jog

parameters described previously are good

examples of settings that can be altered and then persisted in the driver for later use.
To save the settings to hardware, check the ‘Persist Settings to Hardware’ checkbox

before clicking the ‘OK button.

«
...
38
39
40
41
42
...
»

Summary of Contents for RBD201

















































































Reviews:

No comments

Related manuals for RBD201

Brand: FAAC Pages: 4

Brand: FAAC Pages: 52

Brand: Hanwell Pages: 34

Brand: HANSONG Pages: 11

Brand: Datapath Pages: 12

Brand: Hansen Pages: 4

Brand: Jäger Pages: 50

Brand: MAKOT Pages: 6

Brand: NCR Pages: 8

Brand: Watts Pages: 8

infi 90 IMMFP12

Brand: Bailey Pages: 75

iSteam 2.0 Control

Brand: mr. steam Pages: 16

Brand: Sygonix Pages: 12

Brand: Bentel Pages: 88

Brand: Zenith Pages: 20

Brand: Swagelok Pages: 16

Brand: Belkin Pages: 60

Aqua Wireless 8347

Brand: claber Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands