THORLABS K-Cube Piezo Controller User Manual Download Page 68

Page: 68 / 78

Appendix D Piezo Control Method Summary

The 'Piezo' ActiveX Control provides the functionality required for a client application

to control o ne or more of the APT series of piezo controller units. This range of

controllers covers both open and closed loop piezo control in a variety of formats

including compact Cube type controllers, benchtop units and 19" rack based modular

drivers. Note one additional product, the KSG101 K-Cube Strain Gauge reader is

another member of the APT co ntroller range - and can also be accessed using the

Piezo ActiveX Control.
To specify the particular controller being addressed, every unit is factory programmed

with a unique 8-digit serial number. This serial number is key to the operation of the

APT Server software and is used by t he Server to e numerate and communicate

independently with multiple hardware units connected on the same USB bus. Th e

serial number must be specified using the HWSerialNum property before an ActiveX

control instance can communicate with the hardware unit. This can be done at design

time or at run time. Note that the appearance of the ActiveX Control GUI (graphical

user interface) will change to the required format when the serial number has been

entered.
The Methods and Properties of the Piezo ActiveX Control can be used to perform

activities such as selecting output voltages, reading the strain gauge position

feedback, operating open and closed loop modes and enabling force sensing mode.

A brief summary of the methods and propertys applicable to the KPZ101 unit is given

below, for more detailed information and individual parameter descriptiond please see

the on-line help file supplied with the APT server.

Methods

DeleteParamSet

Deletes stored settings for specific controller.

DisableHWChannel

Disables the drive output.

DoEvents

Allows client application to process other activity.

EnableEventDlg

Enables or disables the event dialog box.

EnableHWChannel

Enables the drive output.

GetControlMode

Gets the loop operating mode (open/closed).

GetDispIntensity

Gets the front panel LED display intensity.

GetHubAnalogueChanIn

Gets the hub analogue input channel used for close

loop operation.

GetIPSource

Gets the HV amplifier input source.

GetJogStepSize

Gets the jogging step size.

GetKCubePanelParams

Sets various parameters for the top panel controls

Summary of Contents for K-Cube Piezo Controller















































































Search results

Summary of Contents for K-Cube Piezo Controller

Reviews:

Related manuals for K-Cube Piezo Controller

Brands by name

Popular brands

THORLABS K-Cube Piezo Controller, User Manual

Search results

Summary of Contents for K-Cube Piezo Controller

Reviews:

Related manuals for K-Cube Piezo Controller

Brands by name

Popular brands