THORLABS K-Cube Piezo Controller User Manual Download Page 48

Page: 48 / 78

HA0365T Rev D Jan 2017

Chapter 5

5.6.3 Electrical Connections and Software Settings - Off Hub (Hard Wired)

Operation

The following procedure describes a typical set up, when a KPZ101 piezo driver cube

and a KSG101 Strain Gauge Reader are used to control a piezo actuated stage - see

Fig. 5.13 for a general system schematic diagram..

Fig. 5.13 Typical System Set Up - Off Hub (Hard Wired) Operation

1) Perform the mechanical installation as detailed in Section 3.2. of this manual and

also in the manual supplied with the K-Cube Strain Gauge Reader.

2) Connect the MONITOR terminal on the rear panel of the strain gauge unit to the

EXT IN terminal on the rear panel of the piezo unit.

3) Connect the STRAIN GAUGE I/P terminal on the rear panel of the strain gauge

unit to the Feedback connector on the piezo actuator.

4) Connect the HV OUT termina l on the rear of the Piezo driver to the a ssociated

piezo actuator.

5) Connect the units to their power supplies - see Section 3.3.4. of this manual and

also the manual supplied with the Strain Gauge Readers.

6) Connect the PSU to the main supply and switch ‘ON’. The version number of the

embedded software is displayed on the Piezo unit during boot up. The software

version is useful when requesting technical support.

7) Connect each controller unit to your PC.

8) Windows

should detect the new hardware. Wait while Windows

installs the

drivers for the new hardware - see the Getting Started guide for more information.

9) Run the APTUser utility

Start/All Programs/Thorlabs/APT/APT User.

Note

The USB cable should be no more than 3 metres in length.

Communication lengths in excess of 3 metres can be achieved by using

a powered USB hub).

USB Comms

to piezo actuator

drive terminal

to piezo actuator

feedback terminal

Strain Gauge Reader

MENU

Piezo Controller

MENU

Summary of Contents for K-Cube Piezo Controller















































































Search results

Summary of Contents for K-Cube Piezo Controller

Reviews:

Related manuals for K-Cube Piezo Controller

Brands by name

Popular brands

THORLABS K-Cube Piezo Controller, User Manual

Search results

Summary of Contents for K-Cube Piezo Controller

Reviews:

Related manuals for K-Cube Piezo Controller

Brands by name

Popular brands