THORLABS ITC1 Series Operation Manual Download Page 18 | Manualshive

Page: 18 / 46

background image

© 2018 Thorlabs GmbH

16

ITC1xx

Laser diode AG, photo diode CG, no bias:

Laser diode AG, photo diode AG, no bias:

Laser diode AG, photo diode floating, no bias:

The connection, shown as dashed line, can be made either at the laser or at the ITC1xx con-
nector.

Laser diode AG, photo diode CG, -5 V bias:

Laser diode AG, photo diode AG, +5 V bias:

Attention

Reverse connection of the photo diode can permanently damage the photo diode when using a
bias voltage. Check the control voltage output I

PD

(

) prior to enabling a bias voltage. The

output voltage must be positive!

«
...
16
17
18
19
20
...
»

Summary of Contents for ITC1 Series















































Reviews:

No comments

Related manuals for ITC1 Series

Brand: Ransburg Pages: 49

Brand: Balboa Pages: 2

Brand: Badger Meter Pages: 20

Brand: ZKTeco Pages: 8

Brand: EasyIO Pages: 18

Brand: H3C Pages: 69

Brand: Maclaren Pages: 43

Brand: Lawler Pages: 5

Brand: Eaton Pages: 8

FUTERA XLF Series

Brand: RBI Pages: 128

Brand: RBH Access Technologies Pages: 36

Brand: S&C Pages: 11

Brand: S&C Pages: 24

Brand: S&C Pages: 19

Brand: Union Instruments Pages: 63

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: Apex Toys Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands