background image

!

!

October 25

th

 2013 

www.thonk.co.uk 

13 

TouellSkouarn 
Strakal Brulu Module 

Eurorack DIY Kit 

Instructions 

Version 1.0 

                      

 

 

 

 

 

 

 

 
35. 
 
You  can  now  power  the  module  on.  You  should  use  a  small  Philips 
screwdriver  to  calibrate  the  module  via  the  blue  trimmer.  The  best  advice 
from TouellSkouarn is to just trim by ear, I have found if you have the input 
and output knobs set to midnight and then trim so the feedback knob squeal 
(resonant  self-oscillation)  starts  to  happen  sometime  around  1  -  2  o’clock 
then you have a good range of possibilities… but there is not really a ‘right or 
wrong’ setting for the trimmer. 
 
If you want to follow the official ‘factory’ default from Touellskouarn then with 
the  module  powered  on,  set  your  multimeter  to  read  DC  voltage.  Put  the 
Black  or  COM  probe  on  the  ground  point  shown  on  the  PCB  and  the  Red 
voltage  probe  on  the  ‘C’  or  collector  terminal  of  the  larger  germanium 
transistor. 
 
To start turn the trimmer until the DC voltage is showing approximately -5V to 
-7V. 
 
Not  trimming  the  module  will  not  damage  it,  but  these  values  are  a  good 
starting  point  for  use,  the  trimmer  can  alter  the  sound  quite  radically  in 
interesting ways though so exploration is encouraged. If it sounds good, it’s 
good 

!

 

 

Summary of Contents for TouellSkouarn Strakal Brulu















Reviews: