12
Use
t
u
to select a sub-menu and
pq
to choose an option. Press
OK
to open the chosen
submenu.
7.1 Installation
Press
MENU
and select
Installation
with
t
u
. The following sub-menus are available:
Antenna
Setup
,
Motor Setting
,
Channel Search
and
Factory Reset
.
7.1.1 Antenna Setup
In this menu, you can change and adapt settings for the antenna(s) and their transponders. Use the
t
u
buttons to change settings, and use
pq
to select an item, or press
OK
to list the settings. For
the default setting of
DiSEqC 1.0
, you can set the parameters for up to 4 satellite positions
Port 1-4
.
Satellite
Press
OK
to open the list of available satellites. Select the desired satellite with
pq
or
P+/P-
and confirm with
OK
.
LNB Power
If necessary, you can change the LNB voltage using the
t
u
buttons.
LNB Type
Select the desired LNB type using the
t
u
buttons if you are not using a universal
LNB. Available are:
C Band
,
SatCR
and
User defined
.
LNB Freq
Displays the corresponding values for the LNB type. 4 adjustments are possible.
22 KHz Tone
Not configurable at
Universal
LNB Type.
DiSEqC 1.0
If DiSEqC 1.0 is used, up to 4 positions can be linked to satellites.
DiSEqC 1.1
If DiSEqC 1.1 is used, up to 16 positions can be linked to satellites.
System
If you set
Sat CR
, here you can choose a number from 1-9.
IF Channel
If you are using
Sat CR
, you can set the
IF channel
here.
Center Frequency
If you are using
Sat CR
, you can enter the corresponding frequency here.
Transponder
Press
OK
to open the list of available transponders for the selected satellite to check
the reception or select for channel search on it.
If
Transponder
is highlighted, the channel search can be started on this TP by using the
RED
Search
button or just press
OK
, the
GREEN
Auto DiSEqC Search
* button allows you to search for available
satellites in the existing antenna installation.
* This function can find available satellites within the already persisting installation. The preconfigured satellites are: Astra 19.2E, Astra
23.5E, Astra 28.2E, HotBird 13.0E and Eutelsat 9.0E.
7.1.2 Motor Setting
If you are using
DiSEqC 1.2
or
USALS
, you can install satellites which are received by a motorised
dish. For the correct installation and positioning of your motor, we recommend the support/advice
of a professional and experienced installer. Here you can configure the motor type and set the motor
position for a satellite that you want to receive.
Satellite
Press
OK
to open the list of available satellites and select one by using the
pq
or
P+/P-
buttons, then press
OK
again for confirmation.
Transponder
Press
OK
to open the list of available transponders if you like to set a specific
transponder for the selected satellite.
DiSEqC Motor
Choose between
DiSEqC 1.2
and
USALS
or
Off
. Per default it is Off because of pre-
defined setup for DiSEqC 1.0.
DiSEqC 1.2 selection
Move step-wise
Press
t
u
to move your antenna east or west. Move carefully until you see that
both signal beams have an acceptable reception level. When you find the selected
satellite, press
and select
Yes
to save the position.
Move continuously
Use this function to move quickly to a desired position by holding down the
t
or
u
key, depending on the direction in which you want to move the antenna. Also, be
very careful with it, so you do not bump into obstacles.
Limit
Press
OK
to open this sub-menu, which allows you to set the mechanical limits for
your motor. This is only necessary if your antenna is mounted which means, that a
