3
2). OPENING DETECTOR
When installed on a door or window, this device will detect any attempts at
intrusion (when the magnet is moved, this is detected) and transmits the
information to the Thombox, which triggers the alarm.
Installation
ø4mm
2mm
66mm
22mm
12mm
max
25mm
studs
- Attach the magnet to the wall using
double-sided tape or the screws
provided.
- Attach the magnet opposite the 2
detector studs.
To activate the opening detector:
- Access the accessory's battery compartment by removing the sensor's
cover with a small flat screwdriver, which will serve as a lever.
- Remove the tab which protects the detector's battery (if the tab has already
been removed, remove the battery and put it back in place), the detector
should emit a series of flashes.
- You may now place your sensor in its permanent position, put the cover back
on your detector and replace the screws.
Installation with adjustable mount (included)
You can affix the motion detector to a bracket for wall or ceiling mounting using a
ball-joint mount in order to position the angle of detection.
OR
Wall
mounting
Ceiling
mounting
Wall mounting:
ø4mm
1
2
ON
CTS
3
4
ø8mm
27mm
To activate the motion detector:
- Access the accessory's battery compartment by unscrewing the screw
located under the sensor, then remove the cover from your detector.
- Remove the tab which protects the detector's battery (if the
tab has already been removed, remove the battery and put it back in place),
the detector should emit a series of flashes.
- You may now place your accessory in its permanent position, put the cover
back on your detector (make sure you hear the 'click' when you put the
cover back on) and replace the screws.
3). MOTION DETECTOR
This detector detects the presence of a moving person in the room where it is
installed, and transmits the information to the central unit which sounds an alert.
Choice of location
For effective protection, follow the rules below when choosing where to place your
indoor motion detector:
-
Do not place the detector opposite a window or a source of reflected light.
-
Do not place the detector opposite a source of hot or cold air (radiator, air vent,
etc.).
-
If you are using several detectors to cover the same room, ensure that the
beams do not cross.
-
Place your detector at right angles to the through route (and not in the direction
of the through route).
A-
The detector is facing a mirror (which reflects the sun's rays) and a
fireplace. The through route does not cross the beams at right angles.
B -
The beams are crossing and one detector is opposite a window.
C -
The door and the window are protected and the detector is installed so that
the through route crosses the beams at right angles.
D -
The detector is installed so that the through route crosses the beams at right
angles.
bad
good
A
B
C
D
2.20m
1m
1m
7.5m
15m
Area accessible to animals below the weight threshold (15kg or 25kg, see
settings below)
Zone forbidden to animals (will trigger an alarm)
Note: the range and detection sensitivity can be configured: see the settings below
Operation
The sensor on the front can detect variations in infra-red rays: when a living being
moves in front of the sensor, the motion is detected.
-
An animal moving along the ground will not cause motion to be detected, as
long as its weight does not surpass the weight specified in the settings (15kg or
25kg)
Settings
Different settings can be accessed inside the detector:
21
(&(
-
Switch 1: if it is lowered, this deactivates the LED on the front during a radio
transmission to be more discreet.
-
Switch 2: if it is raised, detected movement triggers an alarm. If it is lowered, an
alarm will only be triggered if 3 detections take place consecutively, in order to
avoid false detections.
-
Switch 3: if it is raised, all radio transmissions are followed by a 2 minute pause
to conserve battery life.
-
Switch 4: sets the size of pets which are not to be detected by the product.
Switch up: <15kg. Switch down: <25kg.
-
Adjustment dial: adjusts the detection range. Turn clockwise to increase the
distance, and turn anti-clockwise to reduce the distance. The range can be set
from around 30% to 100% of the maximum range.
Installation with or without adjustable mount
Installation without adjustable mount
Wall mounting:
ø4mm
1.80m
to 2.40m
view in profile
floor
wall
Corner mounting:
floor
1.80m
to 2.40m
ø4mm
