manualshive.com logo in svg

THOMSON Grass Valley Zodiak, Release Notes

Share
Download
THOMSON Grass Valley Zodiak Release Notes Download Page 37

Zodiak Release Notes

37

Other Zodiak Update Information

 

5.

If there are any problems with any of the restored files, they may have 
become corrupted and need to be deleted and rebuilt. If a problem file 
locks the system, you may need to drain NV RAM again to restore 
system operation, but you will know what file is responsible. Contact 
Grass Valley Group Customer Service if you need troubleshooting 
assistance. 

Note

After NV RAM files are removed, the Still Store will not be prepared for use 
until NV RAM File Saves are enabled. This may take 2 minutes. If you are 
using the Still Store or viewing the Stillstore menus at the time of system 
reset, a Still store disconnected message will appear. Once the files have 
been saved, the Stillstore menu bar will report Still store – connected. You 
will then need to refresh the Stillstore menu manually by making a menu 
change on the Menu panel.

Zodiak System Default IP Addresses

The default IP addresses shipped from the factory have been chosen to 
make Zodiak configuration easy. Numbers were chosen to work with other 
Grass Valley Group devices in a default standalone network configuration.

Table 1.  Default IP Addresses

Device 

IP Address

Address Set/Viewed In:

Video Processor Frame

IP Address: 192.168.54.18 (Menu or Facility LAN)

Web browser

IP Address: 192.168.55.18 (Panel LAN)

Gateway IP: 192.168.54.1 (External Gateway)

Main Panel

Panel IP Address: 192.168.55.8 (Panel LAN)

Web browser or Main Panel Configuration procedure

Panel Gateway IP: 192.168.55.18 (To Menu Panel)

Frame IP Address: 192.168.55.18 (Panel LAN)

Menu IP Address: 192.168.54.8 

Menu Panel

IP Address: 192.168.54.8 (Menu LAN)

Windows 2000 Network and Dial Up Connections

Default Gateway: 192.168.54.1 (External Gateway)

Frame IP: 192.168.54.18 

Eng Setup – System – Config Menu

RT Panel IP: 192.168.55.8 

32 Crosspoint Remote Aux panels
(when hard reset with the front 
panel buttons)

V0.0.2a Software: 
IP Address: 192.168.0.250
Frame IP: 192.168.0.251
Gateway IP: 192.168.0.1
Subnet Mask 255.0.0.0, 

Web browser

Note that 32-Crosspoint Remote Aux panel default IP 
addresses must be changed to operate with a Zodiak 
system whose other components are configured with 
default IP addresses. 

V1.6.5 Software: 
IP Address: 192.168.1.2
Frame IP: 192.168.1.1
Gateway IP: 192.168.1.1
Subnet Mask 255.255.255.0,

Summary of Contents for Grass Valley Zodiak







































Reviews:

No comments

Brands by name

Popular brands

Load more brands