pg. 22
12.3 TROUBLESHOOTING CAUSE-SOLUTION
___________
___________
___________
___________
___________
PROBLEM
CAUSE
SOLUTION
PELLET TANK IS EMPTY
(DISPLAY SHOWS THE INSCRIPTION AL PE)
FILL UP THE TANK
FOREIGN BODY SUCH AS NAIL, NYLON,
PIECE OF WOOD ON THE FEEDER SCREW
ON THE BOTTOM OF THE TANK
( DISPLAY SHOWS THE INSCRIPTION AL PE)
REMOVE THE FOREIGN BODY
SMOKE EXHAUST NOT FREE, OR WITH
TERMINAL THAT OBSTRUCTS THE PASSAGE
OF SMOKE
(DISPLAY SHOWS THE INSCRIPTION AL OP)
CHECK THE SMOKE EXHAUST AS IT COULD BE
DIRTY OR CLOGGED
OUTLET TERMINAL CLOGGED BECAUSE A
GRILL OR TERMINAL HAS BEEN INSERTED
WHICH PREVENTS THE FREE PASSAGE OF
SMOKE
(DISPLAY SHOWS THE INSCRIPTION AL OP)
REMOVE THE TERMI NAL AND REPLACE IT WITH A
MORE SUITABLE ONE.
SUDDEN GUST OF WIND WHICH HAS MADE
THE APPLI ANCE GO INTO SAFETY MODE
(DISPLAY SHOWS THE INSCRIPTION AL OP)
SWITCH THE POWER SUPPLY TO THE HEATER OFF
THEN BACK ON AGAIN
THE PELLET SCREW MOTOR DOES NOT
WORK
REPLACE THE PELLETS SCREW MOTOR
PELLETS DO NOT DROP INTO THE BURNER
THE RESET THERMOSTAT TRIPS AND
LOCKS THE GEARMOTOR
THE ROOM FAN IS BROKEN AND MUST BE
REPLACED; THEN, PUT BACK INTO SERVICE THE
RESET THERMOSTAT, WAIT UNTIL THE HEATER
COOLS DOWN AND RESET THE THERMOSTAT.
THE VENTILATION FILTER IS VERY DIRTY AND MUST
BE CLEANED; THEN, PUT BACK I NTO SERVICE THE
RESET THERMOSTAT, WAIT UNTIL THE HEATER
COOLS DOWN AND RESET THE THERMOSTAT.
SMOKE EXHAUST NOT FREE, OR WITH
TERMINAL THAT OBSTRUCTS THE PASSAGE
OF SMOKE
REMOVE THE TERMI NAL AND REPLACE IT WITH A
MORE SUITABLE ONE. CHECK THE SMOKE EXHAUST
AS IT COULD BE DIRTY OR CLOGGED
BURNER IS DIRTY
CLEAN THE BURNER ON A MORE FREQUENT BASIS
CARRY OUT ALL CLEANING OPERATIONS
INDICATED IN PARA. 8.2
PELLETS WITH DEPOSIT ABOVE
PERMISSIBLE LIMI TS
CLEAN THE BURNER MORE OFTEN.
SET OPERATI NG PROGRAMS P2
THE BURNER IS NOT PROPERLY PLACED ON
I TS SEAT
SET THE BURNER ON ITS SEAT PROPERLY
THE APPLI ANCE ACCUMULATES PELLETS IN THE
BRAZIER WHILE OPERATING
THE BURNER STAYS LIFTED FROM ITS SEAT
SET THE BURNER ON ITS SEAT PROPERLY
OCCURS THE FIRST TIME THE HEATER IS
SWITCHED ON AS THE SILICONE PAINT IS
BEING BAKED
RUN THE HEATER AT FULL POWER FOR 1 HOUR TO
COMPLETE THE BAKING.
THE SMOKE EXHAUST IS NOT SEALED
CORRECTLY
MAKE SURE THAT THE GASKETS HAVE BEEN
FITTED TO THE SMOKE EXHAUST PI PES
I F THE APPLI ANCE STARTS TO SMOKE
AFTER 25 MINUTES: DIRTY BURNER, VERY
DELAYED START.
CLEAN THE BURNER
THE HEATER SMOKES
I F THE APPLI ANCE STARTS TO SMOKE
AFTER 25 MINUTES: DELAYED START
BECAUSE THE SCREW FEEDER IS EMPTY
FILL UP THE TANK
DELAYED START BECAUSE THE SCREW
FEEDER IS EMPTY
(DISPLAY SHOWS THE INSCRIPTION AL AC)
FILL UP THE TANK
DIRTY BURNER, VERY DELAYED START.
(DISPLAY SHOWS THE INSCRIPTION AL AC)
CLEAN THE BURNER
THE APPLI ANCE SHUTS OFF 5 MINUTES AFTE R THE END
OF THE START UP CYCLE
THE 42°C THERMOS TAT IS FAULTY
(DISPLAY SHOWS THE INSCRIPTION AL AC)
REPLACE THE THERMOSTAT
THE HEATER DOES NOT START UP
THE SPARK PLUG IS BLOWN
(DISPLAY SHOWS THE INSCRIPTION AL AC)
REPLACE THE SPARK PLUG
Summary of Contents for ECOTHERM 5000
Page 16: ...pg 16 ...
Page 17: ...pg 17 ...
