background image

WARRANTY

:

  Under  normal  use  the  Company 

warrants  to  the  purchaser  that  defects  in  material 
or workmanship will be repaired or replaced without 
charge (from date of shipment) for a period of: 

Any claim for warranty must be reported to the sales 
offi ce where the product was purchased for authorized 
repair or replacement within the contract terms. 
Subject  to  State  or  Provincial  law  to  the  contrary,  the 
Company  will  not  be  responsible  for  any  expense  for 

installation, removal from service, transportation, or 

damages  of  any  type  whatsoever,  including  damages 

arising from lack of use, business interruptions, or 
incidental or consequential damages.
The Company cannot anticipate or control the 
conditions of product usage and therefore accepts no 
responsibility for the safe application and suitability 

of  its  products  when  used  alone  or  in  combination 
with other products. Tests for the safe application and 

suitability of the products are the sole responsibility of 
the user.

This  warranty  will  be  void  if,  in  the  judgment  of  the 

Company, the damage, failure or defect is the result of:

 

Vibration, radiation, erosion, corrosion, process 
contamination, abnormal process conditions, 
temperature and pressures, unusual surges or 

pulsation,  fouling,  ordinary  wear  and  tear,  lack  of 

maintenance, incorrectly applied utilities such as 

voltage, air, gas, water, and others or any combination 
of the aforementioned causes not specifi cally allowed 

for in the design conditions 

 

Or, any act or omission by the Purchaser, its agents, 
servants  or  independent  contractors  which  for 

greater certainty, but not so as to limit the generality 
of the foregoing, includes physical, chemical or 
mechanical abuse, accident, improper installation 
of the product, improper storage and handling of the 
product, improper application or the misalignment 
of parts.

No  warranty  applies  to  paint  fi nishes  except  for 
manufacturing defects apparent within 30 days from the 

date of installation.

The Company neither assumes nor authorizes any person to 
assume for it any other obligation or liability in connection 

with the product(s).

The Purchaser agrees that all warranty work required after 
the initial commissioning of the product will be provided 

only if the Company has been paid by the Purchaser in full 

accordance with the terms and conditions of the contract.

The Purchaser agrees that the Company makes no 

warranty  or  guarantee,  express,  implied  or  statutory, 
(including  any  warranty  of  merchantability  or  warranty 
of  fi tness  for  a  particular  purpose)  written  or  oral,  of  the 

Article or incidental labour, except as is expressed or 
contained in the agreement herein.

LIABILITY:

 

Technical data contained in the catalog 

or on the website is subject to change without notice. 

The Company reserves the right to make dimensional 
and other design changes as required. The Purchaser 

acknowledges  the  Company  shall  not  be  obligated 

to modify those articles manufactured before the 
formulation of the changes in design or improvements 
of the products by the Company.
The Company shall not be liable to compensate or 
indemnify the Purchaser, end user or any other party 

against  any  actions,  claims,  liabilities,  injury,  loss, 

loss of use, loss of business, damages, indirect or 

consequential  damages,  demands,  penalties,  fi nes, 
expenses (including legal expenses), costs, obligations 
and causes of action of any kind arising wholly or partly 

from negligence or omission of the user or the misuse, 
incorrect application, unsafe application, incorrect 
storage and handling, incorrect installation, lack of 
maintenance, improper maintenance or improper 
operation of products furnished by the Company.

PLEASE ADHERE TO INSTRUCTIONS IN THIS MANUAL

Failure to do so may be dangerous and may void certain 
provisions of your warranty.

    

84 months - SwitchBlade

®

 Heaters

    

60 months - DC Heaters

    

36 months - DC Control Panels

    

36 months - HELLFIRE Heaters, FEB Heaters

    

12 months - All other Fastrax

®

 Products

For further assistance, please call 1.855.244.3128

Summary of Contents for Fastrax













Reviews: