Thermocet Apertura series Operating And Installation Instructions Download Page 3

Page.3 

We wish you happy heating with the purchase of this  gas fire. 
Please read these instructions carefully before you install the fire and start using it. 
Keep these instructions in a safe place. 
Always quote type and serial number in the event of a problem. 
 
 

1. General 

 

The Apertura is delivered complete. You should inspect the appliance for damage in transit immediately on 
delivery. Any damage found should be reported without delay and as precisely as possible to your supplier. 
Please refer to the delivery document in this connection. Your fire is coated with heat-resistant enamel that 
can withstand extremely high temperatures. Burn the fire at high during the first hours of use and ventilate 
the room well. The curing of the enamel may produce a smell/smoke, but this is harmless, however. 
After the window has cooled down, any marks on the glass should be removed immediately with glass 
cleaner. 

 
Important information 

The Apertura must be installed, connected and inspected by a recognized installer, in accordance with na-
tional and regional standards. The appliance must be checked by the installer for gas tightness to gas and 
combustion products and the correct operation of the various components and functions. In addition, the 
flue system and the outlets in external walls or roof surface must comply with current regulations. The fire 
falls within the category of  closed appliances in an installation space, without blower and with a flue loss 
in excess of 17 % (non-condensing). 
 

Guarantee ( see page 21 and 22) 

Always complete your guarantee card in full and return it to your supplier immediately after purchase.  
Type and serial numbers are shown on the plate that you will find in the control box. 
(See Page 12 diagram 1-14). 
 

Contents of package 

1 x Completely mounted appliance: Front, Corner or Panorama 
1 x Flexible gas hose 
4 x Adjustable feet 
2 x Stabilizer plate 
4 x Bolts M6 x 10 
4 x Bolts M6 x30                                 
8 x Nuts M6 
1 x Convection set (2x gr flexible aluminium tube) 
1 x Log set 7 pieces 
1 x Restricting plate 
1 x Bag incandescent granules 
1 x Bag incandescent material 
1 x Control box incl. Remote Control 
1 x 9V block (alkaline recommended) 
4 x AA 1.5V (alkaline recommended) 
1 x Operation and installation instructions 
1 x Guarantee card 
1 x Delivery document 
1 x Mantle iron incl. adjusting bar (depending on model) 
 

 

Summary of Contents for Apertura series























Reviews: