background image

Thermo Scientific

MANUAL NUMBER 057-286-00 (7004301)

       7                  40139                     4/15/15          Updated warranty Information                                                                                         ccs

       6                  31361                     7/18/14          Removed CE reference on pg 2-4                                                                                    ccs

       5                  30954                     4/10/14          Updated Setting TImer for Continuous Shaking Step 3 - pg 5-8                                    ccs

       4                  30461                    10/21/13         Corrected suspension arms part number in Replacement Parts section                        ccs

       3                  29034                     9/10/12          Updated Hyperterminal information                                                                                ccs

       2                  27615                     7/22/11          Revised warranty                                                                                                              ccs

       1                  27135                     3/16/11          Added warranty pages                                                                                                     ccs

       0                      --                         4/20/10          Transfer to Marietta (was 057-286-00 5/15/09)                                                             ccs

    REV             ECR/ECN                   DATE           DESCRIPTION                                                                                                                By 

Preface

MaxQ 7000        i

Models covered in this manual

Model number

Voltage

SHKA7000 (4301)

208V

SHKA7000-1CE (4302)

220-240V

SHKE7000 (4303)

120V

SHKE7000-1CE (4304)

240V

Summary of Contents for SHKA7000














































Reviews: