Thermo Scientific Invitrogen E-Gel A33811 User Manual Download Page 27

Page: 27 / 59

E-Gel

™

Power Snap Electrophoresis System User Guide

Collect DNA fragment

Resume

the run

and carefully observe as

the band of interest fully enters the
recovery well.

Stop the gel and recover the sample with a
pipette. Avoid piercing the agarose.
Some residual DNA will remain visible in

the well due to migration into the agarose
at the bottom of the well.

Proceed with downstream cloning

workflow. No additional gel-purification is
required.

(

Optional

) Collect additional DNA bands in

the same sample from the recovery well by
adding more water to the recovery well
(see page 26).

(

Optional

) Use the

Reverse E-Gel

protocol

if the band of interest passes the recovery
well (see page 20).

Guidelines for estimating run time

•

Refer to the E-Gel

™

1 Kb Plus Express DNA Ladder migration pattern table to estimate

target DNA run time to the reference line.

•

The run times indicated in the table are estimates. Monitor your gel in real time during
the run to ensure the sample does not pass the recovery well.

•

Identically sized bands in different wells may migrate differently.

•

DNA fragment size, amount, and salt content can affect migration rates.

E-Gel

™

1 Kb Plus Express DNA Ladder migration pattern

Ladder

Fragment size

DNA amount (per 25 μL)

Migration time to

reference line

5000 bp

100 ng

~27.5 min

3000 bp

100 ng

~23 min

2000 bp

100 ng

~20.5 min

1500 bp

160 ng

~19 min

1000 bp

90 ng

~17 min

750 bp

90 ng

~16 min

500 bp

180 ng

~15 min

300 bp

90 ng

~14 min

100 bp

90 ng

~13 min

Summary of Contents for Invitrogen E-Gel A33811




























































Search results

Summary of Contents for Invitrogen E-Gel A33811

Reviews:

Related manuals for Invitrogen E-Gel A33811

Brands by name

Popular brands

Thermo Scientific Invitrogen E-Gel A33811, User Manual

Search results

Summary of Contents for Invitrogen E-Gel A33811

Reviews:

Related manuals for Invitrogen E-Gel A33811

Brands by name

Popular brands