Thermo Scientific Evolution One Series User Manual Download | Manualshive

Page: 28 / 42

background image

2

Evolution One Series Spectrophotometers

Spectrophotometer Basics

14

Evolution One Series Spectrophotometer User Guide

Thermo Scientific

Related Topics

Purging the Sample Compartment

Purging the Sample Compartment

Purging the sample compartment removes moisture from the sampling area for subambient
temperature-controlled measurements. When purging the instrument, install sample
compartment windows in addition to purge.

Related Topics

Installing Sample Compartment Windows

Selecting a Purge Gas

Installing Purge

Selecting a Purge Gas

Use dry air or dry nitrogen to reduce or eliminate condensation. The purge gas must be free of
moisture, oil and other reactive materials. To remove particulate matter and oil, install a
10-micrometer filter.

Related Topics

Installing Sample Compartment Windows

Installing Purge

Installing Purge

Use 1/4-inch internal diameter tubing to connect a purge gas source to the purge fitting on
the back of the spectrophotometer.

Related Topics

Installing Sample Compartment Windows

Selecting a Purge Gas

WARNING

Never

use a flammable gas to purge the instrument.

«
...
26
27
28
29
30
...
»

Summary of Contents for Evolution One Series











































Reviews:

No comments

Related manuals for Evolution One Series

Endura AZ20 series

Brand: ABB Pages: 8

Brand: Keithley Pages: 73

Brand: M3S Pages: 40

Brand: Eaton Pages: 87

Brand: Eaton Pages: 16

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: UEi Pages: 8

Prestige Series

Brand: Ibanez Pages: 54

Brand: Panasonic Pages: 1

Brand: Sper scientific Pages: 56

Brand: IDEAL Pages: 84

Brand: Kawai Pages: 72

Brand: Magtrol Pages: 76

Brand: Flexim Pages: 160

Brand: Neriox Pages: 10

Brand: Bartec Pages: 38

Brand: J&D Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands