background image

48

7.

Reconnect the power cord. Turn unit ON.

8.

Reset UV Timer according to “Resetting the UV
Timer.”

9.

Operate normally.

TOC Lamp Replacement

1.

Place unit in the “Idle” mode.

2.

Turn power off. Disconnect the power cord from
the power entry module.

3.

Open right side door and locate the TOC board
at the bottom. The lamp chamber is protruding
from the board on the right side.

4.

Locate the clips on both sides of lamp chamber.
While gently pulling out chamber, wedge a flat
head screwdriver between chamber and clips to
release chamber.

5.

When installing the new lamp chamber, be sure
to carefully insert pins of chamber into left side
row of sockets on TOC board. See

Chamber

Replacement

photo.

6.

Finish installing the new lamp chamber by
securing with clips. Clips may need to be
pushed apart so the chamber will snap back into
place.

7.

Reconnect power cord and reset the TOC lamp
timer. (See “Resetting the TOC Lamp Timer.”)

Fuse Replacement

1.

Turn off the Nanopure TOC - UV and disconnect
it from the power supply by removing the power
cord directly below the main power switch on
right side of unit. Locate the fuse drawer above
the power cord receptacle.

M

AINTENANCE AND

S

ERVICING

Warning

Replace fuses with those of the same
type and rating.

Chamber
Pins

Sockets
used for Pin
Insertion

Chamber Replacement

Clips

Summary of Contents for Barnstead Nanopure TOC - UV





























































Reviews: