![background image](http://html1.mh-extra.com/html/thermo-king/sr-2-smartreefer2/sr-2-smartreefer2_diagnostic-manual_1104380028.webp)
Section 2 – SR-2 Hardware Description
Interface Board Fuse Size & Function
Fuse Size
Function
F1
1A
HPCO Switch Circuit
F2 15A
2AB
Power
F3
40A
Fuel Sol Pull-In/Starter Circuit
F4 None
2A
No fuse - all Bosch alternators
2A fuse - all Prestolite alternators
1
F5 60A
Preheat
Circuit
F6
15A
Damper and High Speed Circuits
F7
2A
8FP Circuit – CAN bus
F8
5A
CAN Connector J12
F9
5A
CAN Connector J14
F10
10A
8X Power - install in upper position
F11
10A
Electric Clutch (Not Used)
F12
5A
CAN Connector J13
F13
2A
8FC Circuit (Remote Lights)
F15
P/S
On/Off Relay
F20 2A
Alternator
Sense
F22
Not
Used
F23
Not
Used
Note 1 - The F4 must be in place for Prestolite
alternators to charge. It must be removed for Bosch
alternators. Note: Service parts interface boards
are shipped without F4 fuse.
F10
There are three in-line fuse clips that allow for
two configurations of the F10 fuse. The upper
position is the normal position. When fuse F10 is
installed in the upper position, control power is
routed to the K9 On/Off Relay contacts. The On/Off
keys on the HMI control panel energize and de-
energize the K9 On/Off Relay. When the K9 On/Off
Relay is energized power is supplied through the
normally open K9 contacts to turn the unit on.
When fuse F10 is installed in the lower position
power bypasses the K9 On/Off relay contacts and
the unit will start and run without the HMI control
panel. Do not operate the unit with the F10 fuse
installed in the lower position unless absolutely
necessary.
IMPORTANT
If fuse F10 is installed in the lower position the
unit will start and run. The HMI Control Panel On
and Off keys will not function. The Off key will
not turn the unit off if Fuse F10 is in the lower
position. If Fuse F10 is in the lower position it
must be removed or the Microprocessor Power
Switch must be turned off to turn the unit off.
F15
The device identified as F15 is a poly switch.
This overcurrent device resets automatically and is
not replaceable.
Interface Board Relay Functions
Important: Do not attempt to remove the relays
from the interface board.
Relay Function
K1 Run
Relay
K2 Preheat
Relay
K3
High Speed Relay
K4 Damper
Relay
K5 Diesel/Electric
Relay
K6
Fuel Solenoid Pull-In Relay
K7 Starter
Relay
K8
Electric Clutch Relay
K9 On/Off
Relay
2-12
31 January 2005
Summary of Contents for SR-2 SmartReefer2
