background image

 

BTH ULTRA  Electric Boilers

 USE & CARE MANUAL 

(Revision  April 2011)

,                                                                                  Page 

19.

 

 

4.11 OPERATION IN DUAL-ENERGY: 

In Dual-energy mode, the display will indicate that this 
mode is active in showing the icon  

 

If it is not shown, check the position of the switch 
located at the back of the controller. It must be set to 
“Bi-Energ” position. 
N.B. The controller will have to be reset to register the 
new mode of operation. Just turn the power OFF and 
back ON to the unit. 
 

Operation in Dual-energy with Electric 

When the authorisation signal to operate in electricity is 
received, (close contact between Ec&E2), the following 
icons will be shown. 
 

 

The circulating pump and the heating elements will be 
activated according to the operating parameters 
established earlier. 
 

Operation in Dual-energy with the auxiliary boiler 

When the authorisation signal will be absent (open 
contact between Ec&E2), the following icons will be 
shown. 

                                    

 

 
Upon reception of a heat demand on terminals TT of 
BTH ULTRA boiler, terminals C1&C2 will be energized 
at 120volts and the pump will be activated. At the same 
time, the contact will close on the 

“AUX” terminals to 

activate the auxiliary boiler. This boiler will be activated 
only when there will be a heat demand to the TT 

terminals and when the auxiliary boiler temperature will 
be lower than the settings of its own temperature 
controls.  
If a three way valve is used on the piping as shown in 
fig.6, it will change position when the contact will close 
on AUX terminals and it will be the end switch of the 
valve that will give the signal to the auxiliary boiler to 
come on. The water flow will then circulate only in the 
auxiliary boiler. 
 

Manual selection for the electricity or auxiliary 
boiler mode. 

If the user wishes to manually select the electricity or 
auxiliary boiler operation, it can be done in following the 
sequence below: 

o

  Push on the 

button for 6 sec. and the 

following icons will appear  

                                         

 

 
The selection of the dual-energy or electric only or 
auxiliary boiler only is made with the + - button. Once 
the selection has been made it will be registered by 
pressing the 

or by waiting for 5sec. 

 
If the electricity only or auxiliary boiler only has been 

selected, the corresponding icon and the 

 icons will 

blink to advise the user that an unusual heating mode 
has been selected. 
 
 
 
 
 

 

 

Summary of Contents for BTH ULTRA 10

























Reviews: