background image

2

ENGLISH

 

 

Dear Customer,

Thank you for preferring a 

T

 heating unit, a mod-

ern, high-quality product that is able to guarantee your maxi-

mum well-being for a long period of time, with high levels of 

reliability and safety. In particular, if working together with a 

Technical Assistance Centre 

T

 that is specifically 

prepared and trained to perform periodic maintenance, your 

unit will remain at maximum efficiency levels at minimum op-

erating costs and if required, replacements with original spare 

parts can be made.

This instruction manual contains important instructions and 

precautions that must be observed to ensure the trouble-free 

installation and efficient functioning of your 

ACQUAHOME 25 B 

BLU

 boiler.

Please accept our renewed thanks for your purchase

Thermital

CONFORMITY

ACQUAHOME 25 B BLU

 boilers conform to the following direc-

tives:

- Directive 92/42/EEC on efficiency requirements

- Electromagnetic Compatibility Directive 2014/30/EU

- Low Voltage Directive 2014/35/EU

- Ecodesign Directive 2009/125/CE for energy-related 

products

- Energy Labelling Directive 2010/30/EU

- Delegated Regulation (EU) N. 811/2013

- Delegated Regulation (EU) N. 813/2013

- Delegated Regulation (EU) N. 814/2013

ENGLISH

Summary of Contents for ACQUAHOME 25 B BLU





















Reviews: