THERM-OZ RENO KIT Instructions Manual Download

Page: 1 / 18

RENO KIT INSTRUCTIONS

PLEASE READ THROUGH ALL PAGES BEFORE

YOU START.

THIS IS TO CONVERT A TWO TAP MANUAL SHOWER SYSTEM ONLY.

IT WILL NOT REPLACE A SINGLE LEVER MIXER VALVE.

5 YEAR WARRANTY ON ALL PARTS AGAINST DEFECTS IN PERFORMANCE

TO BE FITTED BY A QUALIFIED PLUMBER

INSTALLATION IS SUBJECT TO THE REQUIREMENTS OF THE APPLICABLE REGULATORY AUTHORITY,

THE NATIONAL CONSTRUCTION CODE VOLUME THREE

–

PLUMBING CODE OF AUSTRALIA.

AUSTRALIAN STANDARD AS4032.4: 2014 WATERMARK LICENCE WMK26224

NOT TO BE FITTED WHERE FREEZING MAY OCCUR

RECOMMENDED INLET PRESSURE BETWEEN 100 AND 500kPa HOT & COLD EQUAL PRESSURE

If inlet pressure exceeds 500kpa, install a pressure reducing valve soon after the incoming mains supply.

INLET COLD WATER TEMPERATURE BETWEEN 8 and 29°C to obtain set mixed water temperature.

INLET HOT WATER TEMPERATURE BETWEEN 55 and 85°C to obtain set mixed water temperature.

If inlet temperature exceeds 85°C, check hot water system thermostat.

CAN BE FITTED WITH A COMBINATION BOILER, MAINS PRESSURE UNVENTED OR INSTANTANEOUS

HOT WATER SYSTEMS WITH BALANCED PRESSURES

MIXED OUTLET WATER TEMPERATURE RANGE BETWEEN 20 AND 45°C at recommended inlet

temperatures

SAFETY STOP SET FEATURE @38°C with internal safety thermal shut-off

DO NOT USE ABRASIVE CLEANING PRODUCTS

THERM-OZ SHOWERS PTY LTD. 32 GHOST GUM HEIGHTS, JARRAHDALE, WA 6124

ABN 22605 703 231 EMAIL [email protected] PHONE +61 439 1964 41

WEBSITE WWW.THERM-OZ.NET.AU

•

PAGE 1. VITAL INFORMATION

•

PAGE 2. THE PARTS TO USE DEPENDING ON YOUR CURRENT INSTALLATION.

•

PAGE 3. LIST AND DIAGRAM OF ALL RENO KIT PARTS.

•

PAGE 4. INSTALLING RENO KIT IF ONLY USING BOX A PARTS.

•

PAGE 5. INSTALLING RENO KIT IF ALSO USING BOX B PARTS.

•

PAGE 6. IF TAP SPACINGS ARE GREATER OR SMALLER THAN 150mm

•

PAGE 7. FIXING CT100 THERMOSTATIC MIXING VALVE

•

PAGE 8. FITTING THE CHROME HANGING NUT.

•

PAGE 9. SLIDE RAIL KIT AND HAND SET

•

PAGE 10. THERMAL SHUT-OFF & DYNAMIC PRESSURE RATIO

•

PAGE 11. MAINTENANCE & SERVICING

•

PAGE 12. COMMISSIONING

•

PAGE 13. TROUBLE SHOOTING

•

PAGE 14. USER INSTRUCTIONS & ON GOING CARE

•

PAGE 15 & 16 WARRANTY & INSTALLATION DATE

Summary of Contents for RENO KIT



















Search results

Summary of Contents for RENO KIT

Reviews:

Related manuals for RENO KIT

Brands by name

Popular brands

THERM-OZ RENO KIT, Instructions Manual

Search results

Summary of Contents for RENO KIT

Reviews:

Related manuals for RENO KIT

Brands by name

Popular brands