background image

2

4. Installation

•  Ensure the mains supply is switched off and the circuit supply  

fuses are removed or the circuit breaker turned off.

•  Connect the incoming 230V 50Hz supply and outgoing load cables  

to the relevant terminals ensuring correct polarity is observed  
and that all bare conductors are sleeved (see section 5. 
Connection Diagram).

•  A front cable exit cut-out is provided with a pre-installed  

removable cover. 

•  If the front exiting cable cut-out is required:
  1.   Undo the 2 fixing screws and remove the blanking plate  

(you can discard the blanking plate at this stage but keep  
the 2 fixing screws).

  2.  Remove the cable grip from the accessory pack. 
  3.   Using the 2 fixing screws previously removed from  

the blanking plate, secure the load cable to the unit. 

•  Finally secure the unit to the back box with the fixing  

screws provided, forming the cables during installation  
to avoid any entrapment and cable damage.

Power LED

Sets time  
and date

Reset button

Illuminated screen

Output LED

Sets 
programmes

Double pole 
switch

BS 1362 (1"x 

1

/

4

") fuse

Boosts for 1 or  

2 hours and 

decrements 

displayed value 

during time and 

programme 

setting

Override until 

next programme 

change and 

increments 

displayed value 

during time and 

programme 

setting

Summary of Contents for Timeguard SupplyMaster FST24













Reviews: