Theben thePassa P360-221 DALI UP WH, Manual

Page: 6 / 17

6
•
"Office" configuration type (in single and open-plan
offices):
† y
After manual dimming, the constant light control remains
temporarily active with the current brightness value as the
new brightness setpoint value.
† y
The new brightness setpoint value only applies while some-
one is present.
† y
After the lighting time delay, the set brightness setpoint
value is restored.
Switching mode
•
The switching response is controlled by presence and
brightness.
•
The lighting channel switches on in darkness and when
someone is present. The lighting switches off if there is
sufficient brightness or during periods of absence after
the set lighting time delay.
•
The light is switched on with the switch-on dimming
value.
•
The button can be used to change the intensity of the
artificial light when someone is present. If the lighting is
switched on with the button, it remains switched on for
at least 30 min. If people have left the room (before), the
lighting switches off after the set time delay.
Standby (orientation light)
•
After the lighting time delay, the lighting is set to the
standby dimming value (1–25% of the lamp output).
•
The standby time can be set between 0 s and 60 min or
permanently.
•
If the room brightness is above the brightness setpoint
value, the lighting switches off. If the room brightness is
below the brightness setpoint value, the lighting swit-
ches to the standby brightness. If someone reenters the
room, the detector switches back automatically (fully
automatic device) or after pressing the button (semi-
automatic device) to the set brightness setpoint value.
Lighting time delay
•
The minimum time delay (10 s – 60 min) is adjustable
and can increase to max. 30 min or decrease back to the
set minimum time.
•
With settings ≤ 2 min or ≥ 30 min, the time delay
remains unchanged at the set value. If someone briefly
enters and leaves an unoccupied room within 30 s,
the lighting switches off early after 2 min (short-term
presence).
Button control
•
The lighting can be switched or dimmed manually via a
button.
•
A short button press switches the light on or off; a long
button press dims the light (brighter or darker).
•
If the lighting is switched off manually, it remains
switched off as long as people are present. The lighting
switches on again after the time delay has elapsed.
Fully or semi-automatic device
•
Fully automatic device: the lighting is switched on and
off automatically.
•
Semi-automatic device: the lighting must be switched on
manually. It is switched off automatically.
Staircase light function
•
If the staircase light function is activated, the detector is
used as a staircase automatic device. It is not possible to
switch the lighting off manually.
•
If the staircase light function is deactivated, the lighting
can be switched on and off manually.
eco and eco plus
Settings for ideal switching response and maximum energy
savings.
8. Settings
The thePassa P360-221 DALI presence detector features two
different operating modes:
•
Broadcast (factory setting)
•
Addressable
Both operating modes can be selected with the SendoPro or
the theSenda B/app.
Parameter Selection
Type thePassa P360-111 DALI (broadcast)
thePassa P360-221 DALI (addressable)
•
The presence detectors are supplied with basic settings
ready for operation.
•
With SendoPro and the theSenda B/app, parameters can
be checked, adjusted and optimised during start-up.
•
With the theSenda P, parameters can only be adjusted.
Broadcast <thePassa P360-111 DALI>
Teach-in via button
† †
Press the button for > 15 s
▻ The currently measured brightness value is adopted as
the brightness setpoint value.
L
The teach-in function via the button can be disabled using
the SendoPro or the theSenda B/app remote controls
when the "Configuration button/RC" parameter is set to
"disabled".
Parameters via remote control
The following parameters can be checked or changed via
the remote control for support during start-up as well as
servicing:
Parameter Description Can be
checked
by Sendo-
Pro/the-
Senda B
(app)
Can be
changed
by Sen-
doPro/
theSenda
B (app)
Can be
changed
by the-
Senda P
Detection zone
Selection: Z1 / Z2 /
Z1+Z2
x x
Function C1
Selection:
switching/control
x x