Theben thePassa P360-221 DALI UP WH, Manual

Page: 4 / 17

4
6. Start-up
Initial operation of thePassa P360-111 DALI
(broadcast) → factory setting
L
After the start-up phase (30 s), the detector is ready for
operation.
Initial operation of thePassa P360-221 DALI
(addressable), unconfigured system
† †
The operating mode can be switched from broadcast to
addressable with the SendoPro remote control or the the-
Senda B/app:
† †
Select the <thePassa P360-111 DALI> parameter as the
detector type.
† †
Open the DALI configuration ("Control commands" menu in
the SendoPro).
† †
Send the <Change over to addressable operating mode>
parameter to the detector.
† †
After the changeover, select <thePassa P360-221> as the
detector type for further parameterization.
After the first changeover to the addressable operating mode
(thePassa P360-221 DALI), the detector restarts, identifies all
connected DALI lights, assigns short addresses and manages
them in a list.
▻ Depending on the system size, the LED on the detector
flashes (5 x ON briefly every 3 s) for up to 3 min.
If no DALI EBs are connected to the detector or a DALI line is
interrupted
▻ the LED flashes (LED is switched on and flashes 2 x OFF
briefly every 3 s).
If the system is functioning, the detector switches to confi -
guration mode and waits for the configuration of the lighting
groups.
▻ The LED flashes (2 x ON briefly every 3 s).
As long as the configuration has not been carried out, the
system is in the following operating state:
•
Detector is in broadcast mode.
•
Function is in switching mode (only presence detection,
no light measurement).
•
All lights are controlled with 100% switch-on dimming
value.
•
The operating mode is fully automatic device.
•
All connected buttons are active. Switching on and off as
well as dimming are possible.
•
Time delay: 10 min.
Configuring the lighting groups with
•
SendoPro
•
theSenda B/app
•
Buttons or theSenda S
Configuring the lighting groups with SendoPro
Right function button
Right button
Up button
Down button
Left function button
† †
Select "thePassa P360-221 DALI" as the type in the
SendoPro.
† †
Select "Menu" (right function button) then "Control com-
mands" (left function button).
† †
Open "DALI configuration" with "Open" (right function
button).
For the DALI configuration, there are 3 options available:
† y
"Group assignment (unaddress.)": only DALI EBs without a
group address are processed.
† y
"Group assignment (all)": all connected DALI EBs are con-
figured.
NOTE
: All existing group assignments with group
number 1 or 2 are deleted.
† y
"Change group assignment": the next existing EB is
searched for and selected.
†
†
Use the Up or Down button to select the required group
assignment and press "Send" (right function button) to
start the configuration.
L
The remote control must be directed to the detector! The
LED is switched off.
▻ A DALI light starts to pulse (random order).
† †
Select the required C1 or C2 channel with the button and
assign it to the DALI EB by pressing "Send" (right function
button).
▻ As confirmation, the light dims to 20%.
▻ The next DALI light starts to pulse. One after the other,
the lighting groups are assigned to all the lights.
•
For group assignment (unaddress.) or (all): if all DALI EBs
are assigned to a lighting group, the detector terminates
the configuration process and restarts (startup phase of
30 s). The detector then switches to the normal opera-
ting mode and the configuration is completed.
L
If necessary, the configuration process can be ended by
pressing "End" (left function button).
▻ In this case, the system is not ready for operation.
•
If "Change group assignment" has been selected, use the
right ">" button to switch to the next DALI EB without
changing the lighting group.
† †
When all required changes have been made, end the confi -
guration process by pressing "End" (left function button).
Configuring the lighting groups with the theSenda B/app
† †
Connect the theSenda B with the corresponding "theSenda
Plug" app.
† †
Place the theSenda B under the detector (direct the remote
control towards the detector).
† †
Select "thePassa P360-221 DALI" as the type in the "the-
Senda Plug" app.
† †
In the "DALI configuration" menu, select the required group
assignment.