Theben 2080045, Manual

Page: 5 / 14

5
The lighting groups can also be configured using the but -
tons. All connected buttons can be used for configuration. A
detailed description can be found in chapter „9. Start-up“.
Configuration via the buttons can be disabled using the “Sen -
doPro, theSenda B/App” management remote control when
the <Configuration button/RC> parameter is set to “disabled”.
Parameters via remote control
The following parameters can be checked or changed via
the remote control for support during start-up as well as
servicing:
Parameter Description Can be
checked
SendoPro,
theSenda
B/App
Can be
changed
SendoPro,
theSenda
B/App
Can be
changed
theSenda
P
Function C1/C2
Function C3
Selection:
switching/control
x x
Light measure-
ment source C3
Selection: Centre /
Integral
x
Terminal S1
assignment
Terminal S2
assignment
Selection: C1 / C2 /
C1+C2 / C3 / C1+C3
/ C2+C3 / C1+C2+C3
x
Terminal S3/P
assignment
Selection: Parallel /
C1 / C2 / C1+C2 /
C3 / C1+C3 / C2+C3
/ C1+C2+C3
x
Brightness set
point value
C1, C2
Value range in lux/
measurement off
x x x
Brightness set
point value C3
Value range in lux/
measurement off
x x
Brightness
actual value C1,
C2, C3
Query brightness
actual value
x
Room correc-
tion factor Win
Room correction
factor on side
towards window
x x
Brightness
measurement
value Win
Lux meter bright -
ness value on side
towards window
in lux
x x
Room correc-
tion factor Mid
Room correction
factor middle
x x
Brightness
measurement
value Mid
Lux meter bright -
ness value middle
in lux
x
Room correc-
tion factor Inn
Room correction
factor Inn
x x
Brightness
measurement
value Ins
Lux meter bright -
ness value interior
in lux
x
Room correc-
tion factor Int
Room correction
factor Integral
x x
Brightness
measurement
value Int
Lux meter bright -
ness value Integral
in lux
x
Detection sen-
sitivity (PIR)
Value range in
increments
x x x
Lighting time
delay
Value range in
seconds and
minutes
x x
Short presence
Short-term pre-
sence: On/Off
x x
Energy saving
mode
Selection: eco/eco
plus
x x
Presence
switch-on delay
Value range in
seconds/minutes
x
Presence time
delay
Value range in
seconds/minutes
x x
Parameter Description Can be
checked
SendoPro,
theSenda
B/App
Can be
changed
SendoPro,
theSenda
B/App
Can be
changed
theSenda
P
Switch-on
dimming value
C1, C2, C3
Value range in % x
Configuration
type C1/C2
Selection: auto/man x x x
Configuration
type C3
Selection: auto/man x x
Control speed
Selection: standard/
medium/fast
x
Minimum dim-
ming value
Value range in % x
Maximum dim -
ming value
Value range in % x
Switching off
brightness
Value range in
minutes/hours/
never off
x
Manual dim-
ming response
Selection: school/
office
x
Standby time
Value range in
seconds/minutes/
Permanently on
x
Standby dim-
ming value
Value range in % x
IR group
address C1,
C2, C3
Selection: All/I/II/III x
Scene 1 C1
Scene 2 C1
Scene for lighting
channel C1 value
range in %
x
Scene 1 C2
Scene 2 C2
Scene for lighting
channel C2 value
range in %
x
Scene 1 C3
Scene 2 C3
Scene for lighting
channel C3 value
range in %
x
Configuration
button/RC
Selection: enabled/
disabled
x
LED display
motion
Off/On x
The parameters are sent to the presence detector with the
“SendoPro, theSenda B/App” management remote control or
with the “theSenda P” installation remote control via infra-red.
Changed parameters are applied and used by the detector.
L
Ensure that the parameter selection is limited on the „the-
Senda P“ remote control.
With the “SendoPro, theSenda B/App” management remote
control, parameters can be queried by sending values level-
by-level to the detector. If the sent value is below the set
parameter, the LED illuminates briefly. If the sent value is
equal to or above the set parameter, the LED flickers for 2 s.
Function C1, C2
The lighting channels C1 and C2 can be operated together in
the switching operation or constant lighting control function.
Settings are made via the <Function C1/C2> parameter.
Value range (with SendoPro, theSenda B/App)
Switching Lighting channels C1 and C2 are in the switching operating
function
Control Lighting channels C1 and C2 light are in the constant lighting
control function