The Handy THS125 Operator'S Manual And Parts List Download | Manualshive

Page: 11 / 24

background image

- 11 -

STEP 4: Connecting Handle to the Support Leg

1. Slide the handle tube into the top of the support leg and align the two holes.

2. Insert M6x35 hex bolts through the two holes on the support leg and tighten with the Ø6 spring

washer and M6 lock nut.

3. Insert M6x20 hex bolt through the hole in the side plate and tighten with Ø6 spring washer and M6

lock nut.

«
...
9
10
11
12
13
...
»

Summary of Contents for THS125

























Reviews:

No comments

Related manuals for THS125

FlashMover 8-in-1 USB

Brand: Microdia Pages: 4

Brand: IDTECK Pages: 12

Brand: Velleman Pages: 19

Obid ID RWA02.ABC-A

Brand: Feig Electronic Pages: 36

Brand: V.TOP Pages: 9

USB CompactFlash Reader/Writer REX-CF03

Brand: Ratoc Systems Pages: 57

Brand: Roger Pages: 23

Brand: Magtek Pages: 61

Brand: AuthenTrend Pages: 17

Brand: Viking Pages: 20

Brand: FAMOCO Pages: 30

Brand: GE Security Pages: 18

AC5-OS V1.25 Series

Brand: IVDT Pages: 12

Brand: Manhattan Pages: 2

AXIS H 30.1 EMC

Brand: KUHL Pages: 136

Brand: LEHNER Pages: 74

Brand: ID Tech Pages: 10

Brand: Zonet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands