The Container Store Elfa Instructions For Easy Installation & Assembly Download Page 16

Page: 16 / 16

Printed on recyclable paper. Please recycle.

31749 12/16

Top L-Crossbars

Back Stop Pin

Frame

Runners

Side Panel

Top

Side

Panel

Bottom

T-Crossbar

Side Panel

Bottom

Assemble a Single Frame

Combine Frames

Insert Drawers

Position the Side Panels with the runners facing inward.

(Figure A)

Using a plastic mallet, tap the Bottom T-Crossbars into the bottom of each
Side Panel.

Put a Back Stop Pin in the back holes of the top runners. The remaining
Back Stop Pins should be put in place just prior to sliding in the Drawers.

If combining Frames, see instructions below.

If using a Melamine Top

, tap the Top L-Crossbars completely into each Side

Panel. Place adhesive strips included in the packaging on the top L-Crossbars.
Align the Melamine Top with the crossbars and press firmly.

If not using a Melamine Top

, tap the Top L-Crossbars completely into

each Side Panel.

Assemble the top Frame completely. (See Steps 1 and 2 above.)

Assemble the bottom Frame, omitting the Top L-Crossbars.

If using Back Stop Pins, put one in the back of the left and right top runners
of the bottom Frame.

Lower the top frame onto the bottom frame, making sure the Back Stop
Pins are all on the back side. Secure by firmly tapping each corner of
the top frame until Bottom T-Crossbars are completely inserted into the
bottom frame.

(Figure B)

Insert the remaining Back Stop Pins.

Slide in the Drawers.

If you have other elfa Frame and Drawer accessories, add them now.

STEP

Tools needed:

plastic mallet

TIPS for getting started

• If you don’t have a plastic mallet, you can use a hammer with a wood

block to protect the frame.

• If assembling on tile or wood, take care to protect the floor.

Top

Frame

Bottom

Frame

elfa Drawer Units

containerstore.com | 800-733-3532

Visit

containerstore.com/installation

to view video instructions.

Summary of Contents for Elfa

















Search results

Summary of Contents for Elfa

Reviews:

Related manuals for Elfa

Brands by name

Popular brands

The Container Store Elfa, Instructions For Easy Installation & Assembly

Search results

Summary of Contents for Elfa

Reviews:

Related manuals for Elfa

Brands by name

Popular brands