manualshive.com logo in svg

TGM MWVT09S, Service Manual

Share
Download
TGM MWVT09S Service Manual Download Page 46

Service manual 

 

                            - 45 - 

10.2.4    E3(indoor fan speed out of control) diagnosis and solution 

 

 

10.2.5    E5(Open or short circuit of outdoor temperature sensor) diagnosis and solution. 

 

 

10.2.6    E6(open or short circuit of room or evaporator temperature sensor) diagnosis and solution. 

 

 

10.2.7    P0(IGBT over-strong current protection) diagnosis and solution. 

 

 

Is all connections on PCB 
and between PCB and 
compressor good?   

Repair or correct the 
connector or connection. 

Replace the outdoor PCB 
and then repower on. Is 
the failure cleared? 

NO 

YE

Check the compressor 

NO 

Is the indoor temperature 
and evaporator sensor 
connector and connection 
good? 

Repair the connector and 
reconnect 

Replace the sensor and 
check if E6 display again? 

NO 

YES 

Replace the indoor PCB 

YES 

Is the outdoor temperature 
sensor connector and 
connection good? 

Repair the connector and 
reconnect 

Replace the sensor and 
check if E5 display again? 

NO 

YES 

Replace outdoor e-box 

YES 

Is the indoor fan motor 
connector and connection 
good? 

Repair the connector and 
reconnect 

Is voltage being applied to 
the fan motor? 
(rang 90v-160v between 
mid pin and N on CN1 

NO 

YES 

Indoor PCB is defective. 
Replace the indoor PCB. 

YES 

Replace the indoor fan 
motor 

NO 

Summary of Contents for MWVT09S

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands