TFT HURRICANE DUAL HANDWHEEL Series Instructions For Installation, Operation And Maintenance Download Page 1

Page: 1 / 28

©Copyright Task Force Tips LLC 2004-2020

LIX-300 October 23, 2020 Rev22

TASK FORCE TIPS LLC

MADE IN USA · tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 · 219-462-6161 · Fax 219-464-7155

G-Force

INSTRUCTION FOR INSTALLATION, OPERATION, AND MAINTENANCE

HURRICANE™ MONITOR

SERIES

DANGER

Understand manual before use. Operation of this device without understanding the manual and

receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/

serial-number.
This equipment is intended for use by trained and qualified emergency services personnel for

firefighting. All personnel using this equipment shall have completed a course of education

approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize firefighters and maintenance personnel with the

operation, servicing, and safety procedures associated with this product. This manual should be

kept available to all operating and maintenance personnel.

Hurricane

Dual Handwheel

Hurricane

Hurricane Extended

Hurricane Tiller

For 4.5” Quick Connect

and Valve Under Monitor

See

Section 3.3

for

Flow/Pressure Operating Envelope

Summary of Contents for HURRICANE DUAL HANDWHEEL Series





























Search results

Summary of Contents for HURRICANE DUAL HANDWHEEL Series

Reviews:

Related manuals for HURRICANE DUAL HANDWHEEL Series

Brands by name

Popular brands

TFT HURRICANE DUAL HANDWHEEL Series, Instructions For Installation, Operation And Maintenance

Search results

Summary of Contents for HURRICANE DUAL HANDWHEEL Series

Reviews:

Related manuals for HURRICANE DUAL HANDWHEEL Series

Brands by name

Popular brands