background image

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

EK1240LX and EK1240CLX Crimping Tools 

Troubleshooting

Before You Begin

1.  Make sure that the battery is charged. Recheck 

the battery after several minutes to make sure the 

battery is holding its charge.

2.  Use a 

nonflammable

 contact cleaner or pencil 

eraser to clean the electrical contacts on the battery 

and tool.

3.  Reinstall the battery and check the tool again.

Problem

Possible Cause

Probable Remedy

Tool is inoperative.

Battery charge low.

Charge or replace battery.

Dirt, contaminants, etc., in 

ram area of tool.

Clean tool.

Tool components worn or 

damaged.

Contact Greenlee customer service at  

800-435-0786 for warranty service or repair.

Motor is inoperative.

Low or uncharged battery.

Try known charged battery. Inoperative battery may 

be discharged or may have reached life expectancy.

Broken switch components.

Contact Greenlee customer service at  

800-435-0786 for warranty service or repair.

Motor runs but tool will not 

complete a cycle.

Oil level low.

Contact Greenlee customer service at  

800-435-0786 for warranty service or repair.

Air in hydraulic system.

Pull trigger and hold retract button simultane-

ously. Run for approximately 10 seconds, and then 

attempt to crimp. If unsuccessful, contact Greenlee 

customer service at 800-435-0786 for warranty 

service or repair.

Cold oil.

Pull trigger and hold retract button simultaneously 

to warm oil. Store tool in warm area.

Tool loses oil.

Damaged seal.

Contact Greenlee customer service at  

800-435-0786 for warranty service or repair.

Summary of Contents for Greenlee GATOR EK1240CLX













Reviews: