6
3
. Prepare the laminating pouch for inserting into the machine.
See How to load a
laminating pouch below Do not use pouches thicker
than 160mic (2x80mic
per side)
4
. When the machine has reached operating temperature, you may insert the pouch,
(sealed edge first), squarely into the machine until it engages with the rollers.
Never insert a pouch open edge first into the machine.
5
. The pouch will move through the machine and exit at the rear.
6
. During the process the
READY
light may go out as heat is absorbed by the
laminating pouch. This is normal.
7
. Do not cut down Laminating Pouches to Laminate smaller sizes of Paper,
smaller sizes of Pouches are available, see below, please use these.
8
. Turn the laminator to
OFF (O)
after use.
9
. Always remove the plug from the power supply, when the Laminator is not in use
IMPORTANT!
Do not touch the top of the machine during use, as it will get very hot and take
approximately 3-4 hours to cool down. Do not place items on top of the machine at
any time.
Laminating Pouch Sizes:
A4 – 303 x 216mm
A5 – 216 x 154mm
A6 – 154 x 110mm
A7 – 80 x 111mm
ID Card – 90 x 60mm
Credit Card – 86 x 54mm
Laminating capacity:
The LMA4V is a personal laminator designed for hot lamination so is only suitable
for home and small office use only. Do not use the appliance with pouches thicker
than 160 microns in thickness. Maximum Lamination thickness is 0.45mm, excluding
the pouch.
How to load a laminating pouch:
The laminating pouch is sealed along one side. Open the pouch and place the paper
to be laminated centrally inside the pouch as close to the sealed edge as possible.
Ensure there is an equal border all round the paper (e.g.: A4 paper should have a
3mm border). The sealed edge (not the open edges) is placed into the entry slot to
start the lamination process. Always watch the pouch during the
Laminating process to ensure it comes out the other side of the Laminator.
It may wrap around the rollers if not placed squarely and centrally in the entry slot.
In the unlikely event the pouch becomes jammed in the Laminator, please switch off,
do not open the appliance. Only a qualified service engineer should repair the
appliance.
Warranty & service:
Never service the product yourself. The appliance is guaranteed for 12 months from
date of purchase, subject to normal use. If the laminator is under warranty then return
it to the point of purchase for replacement or repair.
●
●
Now, pull the cutting head in a constant movement and with slight downward pressure
along the cutting ruler.
Instruction to change blade
Do not touch the edge of the blades
as
they
are
very
sharp
!
●
Remove the cap at the back of the cutting head
and
open
by
turning
lever
towards
”OPEN” (figure 1
).
●
Place the cap with the Blade in a safe place so you do not injure yourself
(
Figure 2
).
Press the cutting ruler onto the material
and
with
one
hand
,
hold it in place
.
(
Figure 1
) (
Figure 2
)
●
●
The spare Blades are kept in the Yellow housing
.
●
To
remove
one of the
spare Blades slide open the housing lid and remove the Blade
carefully
●
Insert the replaced Blade into the blade housing and close the lid.
●
Turn the trimmer back over again onto a flat surface.
●
Insert the new Blade into the cutting head. The axis of the Blade must be inserted
properly into the middle
of
the
cutting
head
(
Figure 3 & Figure 4
).
Turn the Paper Trimmer over onto a non-slip
surface
.
(
Figure 3
) (
Figure 4
)
●
locks into
place
(
Figure 5
).
Place the cap back onto the cutting head and turn it towards
“
LOCK
”
until
it
This hand operated trimmer is only suitable for persons aged 16+
;
persons
over
the
age
of 12 years
but
under
the
age
of 16,
may
however
use
the
device
while under
the
supervision
of
an
adult
.
(
Figure 5
)
www.texet.com
