Texas Instruments TPS65917-Q1 Technical Reference Manual Download Page 83

Page: 83 / 181

www.ti.com

FUNC_PMU_CONTROL Registers

SLVUAH1C – June 2015 – Revised April 2017

Submit Documentation Feedback

Register Descriptions

3.7.12 PMU_CONFIG Register (Address = 1B2h) [reset = X]

PMU_CONFIG is shown in

Figure 3-68

and described in

Table 3-75

Return to

Summary Table

PMU configuration
RESET register domain: HWRST

Figure 3-68. PMU_CONFIG Register

RESERVED

HIGH_VCC_SE

NSE

PLL_AUTO_CTRL

SWOFF_DLY

RESERVED

AUTODEVON

R-0h

R/W-X

R-0h

R/W-X

Table 3-75. PMU_CONFIG Register Field Descriptions

Bit

Field

Type

Reset

Description

RESERVED

HIGH_VCC_SENSE

R/W

Enable input buffer for VCC_SENSE input to reduce input leakage.

Rrecommended when VCC_SENSE is >5V

0: VCC_SENSE input buffer is not enabled

1: VCC_SENSE input buffer is enabled

5-4

PLL_AUTO_CTRL

R/W

Enable/disable PLL under different device mode:

00 : PLL is not enabled/disabled automatically. PLL enable
command should be stored in OTP for power sequence.

01 : Enable PLL in ACTIVE mode at the start point of OFF2ACT
transition. Disabled at the end point of ACT2OFF.

10 : Enable PLL in SLEEP mode only.

11 : Enable PLL in both of ACTIVE mode and SLEEP mode at the
start point of OFF2ACT transition. Disabled at the end point of
ACT2OFF.

3-2

SWOFF_DLY

R/W

Delay before to go to SWITCH-OFF to allow host processor to save
his context (device will be maintained ACTIVE until delay expiration
then SWITCH-OFF)

00: no delay

01: 1 second window (+/- 250ms)

10: 2 second window (+/- 250ms)

11: 4 second window (+/- 250ms)

RESERVED

AUTODEVON

R/W

Selection of the feature Auto Device ON

0: Feature is inactive

1: Feature is active

Summary of Contents for TPS65917-Q1






















































































































































































Search results

Summary of Contents for TPS65917-Q1

Reviews:

Related manuals for TPS65917-Q1

Brands by name

Popular brands

Texas Instruments TPS65917-Q1, Technical Reference Manual

Search results

Summary of Contents for TPS65917-Q1

Reviews:

Related manuals for TPS65917-Q1

Brands by name

Popular brands