Texas Instruments TMS320C6201 Reference Manual Download Page 378 | Manualshive

Page: 378 / 477

background image

Programmable Clock and Framing

11-60

These figures show what happens to CLKG when it is initially in sync and
GSYNC = 1, as well as when it is not in sync with the frame synchronization
and GSYNC = 1.

When GSYNC = 1, the transmitter can operate synchronously with the receiv-
er, provided that the following conditions are met:

-

FSX is programmed to be driven by the sample rate generator frame sync,
FSG (FSGM = 1 in the SRGR and FSXM = 1 in the PCR). If the input FSR
has timing that enables it to be sampled by the falling edge of CLKG, it can
be used instead by setting FSXM = 0 in the PCR and connecting FSR to
FSX externally.

-

The sample-rate generator clock should drive the transmit and receive bit
clock (CLK(R/X)M = 1 in the SPCR). Therefore, the CLK(R/X) pin should
not be driven by any other source.

11.5.2.5 Digital Loopback Mode: DLB

Setting DLB = 1 in the SPCR enables digital loopback mode. In DLB mode, DR,
FSR, and CLKR are internally connected through multiplexers to DX, FSX, and
CLKX, respectively, as shown in Figure 11–37. DLB mode allows testing of se-
rial port code with a single DSP device.

11.5.2.6 Receive Clock Selection: DLB, CLKRM

Table 11–15 shows how the digital loopback bit (DLB) and the CLKRM bit in
the PCR select the receiver clock. In digital loopback mode (DLB = 1), the
transmitter clock drives the receiver. CLKRM determines whether the CLKR
pin is an input or an output.

Table 11–15. Receive Clock Selection

DLB

in SPCR

CLKRM

in PCR

Source of Receive Clock

CLKR Function

0

0

CLKR acts as an input driven by the
external clock and inverted as deter-
mined by CLKRP before being used.

Input

0

1

The sample rate generator clock
(CLKG) drives CLKR.

Output. CLKG inverted as determined by
CLKRP before being driven out on CLKR.

1

0

CLKX_int drives the receive clock
CLKR_int as selected and is in-
verted. See Table 11–16.

High impedance

1

1

CLKX_int drives CLKR_int as se-
lected and is inverted. See
Table 11–16.

Output. CLKR (same as CLKX) inverted as
determined by CLKRP before being driven
out.

«
...
376
377
378
379
380
...
»

Summary of Contents for TMS320C6201






























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320C6201

Brand: Danfoss Pages: 61

Brand: TC-Helicon Pages: 2

F-ZTAT H8/3048 Series

Brand: Renesas Pages: 34

Brand: Black Box Pages: 37

Magic WiFi mini Ek

Brand: Devolo Pages: 22

Brand: ROE Pages: 41

Brand: Taiwan Commate Computer Inc. Pages: 29

Brand: QuickLink Pages: 8

Brand: Omron Pages: 29

Brand: IBM Pages: 242

Brand: Wavtech Pages: 8

SNMP-1000-E2B1E

Brand: Advantech Pages: 4

Brand: Omron Pages: 4

Brand: WiebeTech Pages: 8

Brand: Forcepoint Pages: 2

Brand: TERSUS Pages: 7

Brand: Altronix Pages: 8

NVR52A16-16P-4KS2

Brand: Dahua Technology Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands