manualshive.com logo in svg

Texas Instruments Stellaris, User Manual

Share
Download
Texas Instruments Stellaris User Manual Download Page 29

Stellaris® Stepper Motor RDK User’s Manual

November 4, 2009

29

Deceleration

This parameter is the rate at which the motor decelerates from the target speed to stop at the 
target position. Typically, the motor can decelerate faster than accelerate since the load and 
friction are working to help decelerate the motor.

Motor Drive Configuration

Winding Resistance

This parameter sets the resistance of the winding. It should be obtained from the motor 
specification. This value is used in calculating the correct duty cycle if PWM mode is used.

PWM Frequency

If PWM mode is used, this parameter determines the PWM period.

Fixed Rise Time

If PWM mode is used, this parameter sets the amount of time at the beginning of a step that the 
winding is left with full voltage applied before PWM is used to control the current. By leaving the full 
voltage applied to the winding, the current rises as fast as possible, allowing it to reach the drive 
current faster.

Caution – If making adjustments to this value, do not exceed the motor’s rated current. Use lab 
equipment to measure the current in the winding when making adjustments to this value.

ID

Units

Range

Default

PARAM_DECEL

steps/sec

2

100–60000

60000

ID

Units

Range

Default

PARAM_RESISTANCE

m

Ω

100–5000

750

ID

Units

Range

Default

PARAM_PWM_FREQUENCY

Hz

16000–32000

20000

ID

Units

Range

Default

PARAM_FIXED_ON_TIME

μ

S

1–10000

800

Summary of Contents for Stellaris














































Reviews:

No comments

Brands by name

Popular brands

Load more brands