background image

Multiplexer Module (TX2A/TX4A)

                                                  18 November 1996

MUX-2

Edition Notice:

Second Edition - November 1996

This is the second edition of this manual, it describes the following equipment:

TIRIS 2-channel Transmit/Receive Multiplexer Module 

RI-MOD-TX2A

TIRIS 4-channel Transmit/Receive Multiplexer Module 

RI-MOD-TX4A

The text on page 13 about Jumper J5 has been changed to include the S25x0 Reader and a new
figure (figure 6) showing how to connect the Multiplexer Module to the S25x0 has been
included.

Texas Instruments reserves the right to change its products or services at any time without
notice.  TI provides customer assistance in various technical areas, but does not have full access
to data concerning the uses and applications of customer's products.  Therefore TI assumes no
responsibility for customer product design or for infringement of patents and/or the rights of
third parties, which may result from assistance provided by TI.

The 

TIRIS 

logo and the word 

TIRIS 

are registered trademarks of Texas Instruments

Incorporated.

Copyright 

 1996 Texas Instruments Incorporated.

All rights reserved.

Summary of Contents for RI-MOD-TX2A



















Reviews: